SIIG 04 0205F User Manual

Low Profile USB 2.0  
QuickInstallationGuide  
FeaturesandBenefits  
Compliant with USB specifications revision 2.0  
Conforms to PCI specifications revision 2.2  
Supports simultaneous operation of multiple  
high-speed USB 2.0 and USB 1.1 devices  
Supports high-speed (480 Mbps), full-speed (12  
Mbps), and low-speed (1.5 Mbps) data transfer  
modes  
User friendly hot-swapping feature allows you to  
attach/remove USB devices without turning off  
your system  
Note: USB 1.1 devices are limited to USB 1.1 speeds  
evenwhentheyareconnectedtoUSB2.0hostadapter  
or USB 2.0 hubs.  
SystemRequirements  
®
Pentium class computer with an available PCI slot  
®
Windows 7 (32-/64-bit) / Vista (32-/64-bit) / XP  
(32-/64-bit)/Server2003&2008(32-/64-bit)/2000  
SP4  
Dimensions  
PCB: 119.91 mm (L) x 64.41 mm (H)  
Bracket: 18.42 mm (W) x 79.20 MM (H)  
04-0205F  
1
3. Remove the slot bracket from an available PCI slot.  
4. Carefully align the card to the selected PCI slot,  
push the board down firmly, but gently, until it is  
well seated.  
5. Replace the slot bracket holding screw to secure the  
card.  
6. Replacethecomputercoverandreconnectthepower  
cord.  
Driver Installation  
The Low Profile USB 2.0 has three built-in USB hosts. Two  
hosts handle USB 1.1 devices and the third host handles  
USB 2.0 devices. USB 1.1 and USB 2.0 devices are  
automatically routed to the correct USB hosts.  
WindowsDriverInstallation  
Windows 7, Vista, XP, Server 2003 & 2008 and 2000  
Service Pack 4 have built-in driver support for this  
controller. Just install the board and Windows will  
automatically detect and install the correct drivers for it.  
No additional driver is necessary.  
ToVerifyWindowsInstallation  
1. Check Device Manager to verify installation.  
For Windows 7 / XP / Server 2003 / 2000: Right click  
Computer or My Computer, click Manage, click  
Device Manager.  
For Windows Vista: Right click Computer, click  
Manage, click Continue, click Device Manager.  
ForWindowsServer2008:RightclickComputer,click  
Manage, double click Diagnostics, click Device  
Manager.  
3
2. The drivers show up differently under different  
versions of Windows. Please refer to the correct  
Windows version to verify.  
For Windows 7 / Vista: Under Universal Serial Bus  
controllers, NEC to PCI Universal Host Controller  
will be displayed two times and Standard  
Enhanced PCI to USB Host Controller will be  
displayed one time.  
For Windows XP / Server 2003 & 2008 / 2000: Under  
Universal Serial Bus controllers, NEC PCI to USB  
Open Host Controller will be displayed two times  
and NEC to PCI Enhanced Host Controller will be  
displayed one time.  
4
Blank Page  
5
Blank Page  
6
Technical Support and Warranty  
QUESTIONS? SIIGsOnlineSupporthasanswers! Simplyvisitour  
web site at www.siig.com and click Support. Our online support  
database is updated daily with new drivers and solutions. Answers  
toyourquestionscouldbejustafewclicksaway. Youcanalsosubmit  
questions online and a technical support analysts will promptly  
respond.  
SIIGoffersalifetimemanufacturerwarrantywiththisproduct. Please  
see our web site for more warranty details. If you encounter any  
problems with this product, please follow the procedures below.  
A) If it is within the store's return policy period, please return the  
product to the store where you purchased from.  
B) Ifyourpurchasehaspassedthestore'sreturnpolicyperiod,please  
follow these steps to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Go to www.siig.com, click Support, then RMA to submit a  
request to SIIG RMA. If the product is determined to be  
defective, an RMA number will be issued.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All software, cable(s)  
and any other accessories that came with the original package  
must be included.  
Clearly write your RMA number on the top of the returned  
package. SIIG will refuse to accept any shipping package, and  
will not be responsible for a product returned without an  
RMA number posted on the outside of the shipping carton.  
You are responsible for the cost of shipping. Ship the product  
to the following address:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
RMA#:  
SIIG will ship the repaired or replaced product via Ground  
in the U.S. and International Economy outside of the U.S. at  
no cost to the customer.  
7
About SIIG, Inc.  
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer  
of I/O connectivity products, including PCIe, PCI & ISA serial and  
parallel ports, USB, Serial ATA & UltraATA controllers, FireWire  
(1394a/b),networking,soundcards,andotheraccessories. SIIGisthe  
premierone-stopsourceofupgrades.  
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendly  
features, and are backed by an extensive manufacturer warranty.  
High-quality control standards are evident by the overall ease of  
installation and compatibility of our products, as well as one of the  
lowest defective return rates in the industry. SIIG products can be  
found in computer retail stores, mail order catalogs, through major  
distributors, system integrators, and VARs in the Americas and the  
UK,andthroughe-commercesites.  
PRODUCT NAME  
Low Profile USB 2.0  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS  
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not cause  
harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
Phone: 510-657-8688  
LowProfileUSB2.0isatrademarkofSIIG,Inc. SIIGandtheSIIGlogoareregisteredtrademarksofSIIG,  
Inc. Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of  
MicrosoftCorporationintheUnitedStatesand/orothercountries. Pentiumisaregisteredtrademark  
of Intel Corporation. Other names used in this publication are for identification only and may be  
trademarksoftheirrespectivecompanies.  
June, 2009  
Copyright © 2009 by SIIG, Inc. All rights reserved.  

West Bend QUIKSERVE User Manual
Uniden MHS 350 User Manual
TRENDnet NSPEED TEW 649UB User Manual
Sony CD RW Drive CRX225A User Manual
Seagate ST9655AG User Manual
SanDisk Memory Stick Duo User Manual
Samsung Cell Phone SGH I727_UM User Manual
Philips 21PT5006 User Manual
Pantech NULL C3 User Manual
Nokia E90 User Manual