Sharp Flat Panel Television LC 32SB27U User Manual

LC-32SB27U  
LIQUID CRYSTAL  
TELEVISION  
OPERATION MANUAL  
ENGLISH  
IMPORTANT : Please read this operation manual  
before starting operating the equipment.  
Supplied Accessories  
Make sure the following accessories are provided with the product.  
Remote control unit  
1)  
“AA” size battery  
2)  
AC cord  
1)  
Page 8  
Stand unit  
1)  
Page 7  
Operation manual  
3 languages)  
(
(
(
(
(
g
g
g
g
g
Page 8  
Page 9  
• Always use the AC cord supplied with the TV.  
To avoid scratching the frame or screen, please use a soft, lint free cloth for cleaning. Approved  
cleaning cloths are available directly from Sharp in single (00Z-LCD-CLOTH) or triple (00Z-LCD-  
1
 
IMPORTANT INFORMATION  
DECLARATION OF CONFORMITY:  
SHARP LIQUID CRYSTAL TELEVISION, MODEL LC-32SB27U  
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two  
conditions:  
(1) This device may not cause harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
RESPONSIBLE PARTY:  
SHARP ELECTRONICS CORPORATION  
Sharp Plaza, Mahwah, New Jersey 07495-1163  
TEL: 1-800-BE-SHARP  
INFORMATION:  
This equipment has been tested and found to comply with the limits for a Class B digital device,  
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection  
against harmful interference in a residential installation. This equipment generates, uses and can  
radiate radio frequency energy and, if not installed and used in accordance with the instructions, may  
cause harmful interference to radio communications. However, there is no guarantee that interference  
will not occur in a particular installation. If this equipment does cause harmful interference to radio or  
television reception, which can be determined by turning the equipment off and on, the user is  
encouraged to try to correct the interference by one or more of the following measures:  
Reorient or relocate the receiving antenna.  
Increase the separation between the equipment and receiver.  
Connect the equipment into an outlet on a circuit different from that to which the receiver is  
connected.  
Consult the dealer or an experienced radio/TV technician for help.  
"Note to CATV system installer: This reminder is provided to call the CATV system installer's attention to Article 820-40 of the  
National Electrical Code that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall  
be connected to the grounding system of the building, as close to the point of cable entry as practical."  
This product utilizes tin-lead solder, and fluorescent lamp  
containing a small amount of mercury. Disposal of these  
materials may be regulated due to environmental considerations.  
For disposal or recycling information, please contact your local  
Sharp at 1-800-BE-SHARP  
(For U.S.A. only)  
Trademarks  
Manufactured under license from Dolby Laboratories. "Dolby" and the double-D symbol are trademarks of  
Dolby Laboratories.  
"HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of  
HDMI Licensing LLC."  
Products that have earned the ENERGY STAR are designed to protect the environment through superior  
energy efficiency.  
3
 
DEAR SHARP CUSTOMER  
Thank you for your purchase of the Sharp Liquid Crystal Television. To ensure safety and many years  
of trouble-free operation of your product, please read the Important Safety Instructions carefully before  
using this product.  
IMPORTANT SAFETY INSTRUCTIONS  
Electricity is used to perform many useful functions, but it can also cause personal injuries and property damage  
if improperly handled. This product has been engineered and manufactured with the highest priority on safety.  
However, improper use can result in electric shock and/or fire. In order to prevent potential danger, please  
observe the following instructions when installing, operating and cleaning the product. To ensure your safety  
and prolong the service life of your Liquid Crystal Television, please read the following precautions carefully  
before using the product.  
1) Read these instructions.  
2) Keep these instructions.  
3) Heed all warnings.  
4) Follow all instructions.  
5) Do not use this apparatus near water.  
6) Clean only with dry cloth.  
7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.  
8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including  
amplifiers) that produce heat.  
9) Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades  
with one wider than the other. A grounding type plug has two blades and a third grounding prong. The  
wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet,  
consult an electrician for replacement of the obsolete outlet.  
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles,  
and the point where they exit from the apparatus.  
11) Only use attachments/accessories specified by the manufacturer.  
12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold  
with the apparatus. When a cart is used, use caution when moving the cart/apparatus  
combination to avoid injury from tip-over.  
13) Unplug this apparatus during lightning storms or when unused for long periods of time.  
14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been  
damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects  
have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate  
normally, or has been dropped.  
Additional Safety Information  
15) Power Sources—This product should be operated only from the type of power source indicated on the  
marking label. If you are not sure of the type of power supply to your home, consult your product dealer or  
local power company. For products intended to operate from battery power, or other sources, refer to the  
operating instructions.  
16) Overloading—Do not overload wall outlets, extension cords, or integral convenience receptacles as this  
can result in a risk of fire or electric shock.  
17) Object and Liquid Entry—Never push objects of any kind into this product through openings as they may  
touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill  
liquid of any kind on the product.  
18) Damage Requiring Service—Unplug this product from the wall outlet and refer servicing to qualified  
service personnel under the following conditions:  
a) When the AC cord or plug is damaged,  
b) If liquid has been spilled, or objects have fallen into the product,  
c) If the product has been exposed to rain or water,  
d) If the product does not operate normally by following the operating instructions.  
Adjust only those controls that are covered by the operating instructions as an improper adjustment  
of other controls may result in damage and will often require extensive work by a qualified technician  
to restore the product to its normal operation,  
e) If the product has been dropped or damaged in any way, and  
f) When the product exhibits a distinct change in performance - this indicates a need for service.  
19) Replacement Parts—When replacement parts are required, be sure the service technician has used  
replacement parts specified by the manufacturer or have the same characteristics as the original part.  
Unauthorized substitutions may result in fire, electric shock, or other hazards.  
20) Safety Check—Upon completion of any service or repairs to this product, ask the service technician to  
perform safety checks to determine that the product is in proper operating condition.  
21) Wall or ceiling mounting—When mounting the product on a wall or ceiling, be sure to install the product  
according to the method recommended by the manufacturer.  
4
 
IMPORTANT SAFETY INSTRUCTIONS  
EXAMPLE OF ANTENNA GROUNDING AS PER  
NATIONAL ELECTRICAL CODE, ANSI/NFPA 70  
• Outdoor Antenna Grounding — If an outside antenna is  
connected to the television equipment, be sure the antenna  
system is grounded so as to provide some protection against  
voltage surges and built-up static charges.  
ANTENNA  
LEAD IN WIRE  
Article 810 of the National Electrical Code, ANSI/NFPA 70,  
provides information with regard to proper grounding of the  
mast and supporting structure, grounding of the lead-in wire  
to an antenna discharge unit, size of grounding conductors,  
location of antenna-discharge unit, connection to grounding  
electrodes, and requirements for the grounding electrode.  
GROUND  
CLAMP  
ANTENNA  
DISCHARGE UNIT  
(NEC SECTION 810-20)  
ELECTRIC  
SERVICE  
EQUIPMENT  
GROUNDING  
CONDUCTORS  
(NEC SECTION 810-21)  
GROUND CLAMPS  
POWER SERVICE GROUNDING  
ELECTRODE SYSTEM  
(NEC ART 250, PART H)  
NEC — NATIONAL ELECTRICAL CODE  
• Turn off the main power and unplug the AC cord from the wall outlet before handling.  
• Use a soft cloth and gently wipe the surface of the display panel. Using a hard cloth may  
scratch the panel surface.  
• Use a soft damp cloth to gently wipe the panel when it is really dirty.  
(It may scratch the panel surface when wiped strongly.)  
• If the panel is dusty, use an anti-static brush, which is commercially available, to clean it.  
• To protect the panel, do not use a dirty cloth, liquid cleaners or chemical cloth to clean it, such materials may damage the  
panel surface.  
• To clean the outer cabinet, use the same method. Do not use liquid or aerosol cleaners.  
• Water and Moisture — Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or  
laundry tub; in a wet basement; or near a swimming pool; and the like.  
• Stand — Do not place the product on an unstable cart, stand, tripod or table. Placing the product on an unstable base can  
cause the product to fall, resulting in serious personal injuries as well as damage to the product. Use only a cart, stand,  
tripod, bracket or table recommended by the manufacturer or sold with the product. When mounting the product on a wall,  
be sure to follow the manufacturer's instructions. Use only the mounting hardware recommended by the manufacturer.  
• Selecting the location — Select a place with no direct sunlight and good ventilation.  
• Ventilation — The vents and other openings in the cabinet are designed for ventilation. Do not cover or block these vents  
and openings since insufficient ventilation can cause overheating and/or shorten the life of the product. Do not place the  
product on a bed, sofa, rug or other similar surface, since they can block ventilation openings. This product is not designed  
for built-in installation; do not place the product in an enclosed place such as a bookcase or rack, unless proper ventilation  
is provided or the manufacturer's instructions are followed.  
• The Liquid Crystal panel used in this product is made of glass. Therefore, it can break when the product is dropped or  
applied with impact. Be careful not to be injured by broken glass pieces in case the panel breaks.  
• Heat — The product should be situated away from heat sources such as radiators, heat registers, stoves, or other  
products (including amplifiers) that produce heat.  
• The Liquid Crystal panel is a very high technology product with 1,049,088 pixels, giving you fine picture details.  
Occasionally, a few non-active pixels may appear on the screen as a fixed point of blue, green or red. Please note that this  
does not affect the performance of your product.  
• Lightning — For added protection for this television equipment during a lightning storm, or when it is left unattended and  
unused for long periods of time, unplug it from the wall outlet and disconnect the antenna. This will prevent damage to the  
equipment due to lightning and power-line surges.  
• Power Lines — An outside antenna system should not be located in the vicinity of overhead power lines or other electric  
light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system,  
extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.  
• To prevent fire, never place any type of candle or flames on the top or near the TV set.  
• To prevent fire or shock hazard, do not place the AC cord under the TV set or other heavy items.  
• Do not display a still picture for a long time, as this could cause an afterimage to remain.  
• To prevent fire or shock hazard, do not expose this product to dripping or splashing.  
No objects filled with liquids, such as vases, should be placed on the product.  
• Do not insert foreign objects into the product. Inserting objects in the air vents or other openings may  
result in fire or electric shock. Exercise special caution when using the product around children.  
Precautions when transporting the TV  
• When transporting the TV, never carry it by holding or otherwise putting pressure onto the display. Be sure to always carry  
the TV by two people holding it with two hands — one hand on each side of the TV.  
5
 
IMPORTANT SAFETY INSTRUCTIONS  
CHILD SAFETY:  
It Makes A Difference How and Where You Use Your Flat Panel Display  
Congratulations on your purchase! As you enjoy your new product, please keep these safety tips in mind:  
THE ISSUE  
The home theater entertainment experience is a growing trend and larger flat panel  
displays are popular purchases. However, flat panel displays are not always supported  
on the proper stands or installed according to the manufacturer’s recommendations.  
Flat panel displays that are inappropriately situated on dressers, bookcases, shelves,  
desks, speakers, chests or carts may fall over and cause injury.  
THIS MANUFACTURER CARES!  
The consumer electronics industry is committed to making home entertainment enjoyable  
and safe.  
TUNE INTO SAFETY  
One size does NOT fit all. Follow the manufacturer’s recommendations for the safe  
installation and use of your flat panel display.  
Carefully read and understand all enclosed instructions for proper use of this product.  
Don’t allow children to climb on or play with furniture and television sets.  
Don’t place flat panel displays on furniture that can easily be used as steps, such as  
a chest of drawers.  
Remember that children can become excited while watching a program, especially  
on a “larger than life” flat panel display. Care should be taken to place or install the  
display where it cannot be pushed, pulled over, or knocked down.  
Care should be taken to route all cords and cables connected to the flat panel  
display so that they cannot be pulled or grabbed by curious children.  
WALL MOUNTING: IF YOU DECIDE TO WALL MOUNT YOUR FLAT  
PANEL DISPLAY, ALWAYS:  
Use a mount that has been recommended by the display manufacturer and/or listed  
by an independent laboratory (such as UL, CSA, ETL).  
Follow all instructions supplied by the display and wall mount manufacturers.  
If you have any doubts about your ability to safely install your flat panel display,  
contact your retailer about professional installation.  
Make sure that the wall where you are mounting the display is appropriate. Some  
wall mounts are not designed to be mounted to walls with steel studs or old cinder  
block construction. If you are unsure, contact a professional installer.  
A minimum of two people are required for installation. Flat panel displays can be  
heavy.  
Note: CEA is the preeminent trade association promoting growth in the $161 billion U.S.  
consumer electronics industry. More than 2,200 companies enjoy the benefits of CEA  
membership, including legislative advocacy, market research, technical training and education,  
industry promotion and the fostering of business and strategic relationships.  
6
 
QUICK REFERENCE  
Attaching/Detaching the Stand  
Setting the TV on the Wall  
• Before attaching (or detaching) the stand, unplug the AC  
cord from the AC INPUT terminal.  
CAUTION  
• Before performing work spread cushioning over the base  
area to lay the TV on. This will prevent it from being  
damaged.  
• This TV should be mounted on the wall only with the  
AN-37AG5 (SHARP) wall mount bracket. The use of  
other wall mount brackets may result in an unstable  
installation and may cause serious injuries.  
• Installing the TV requires special skill that should  
only be performed by qualified service personnel.  
Customers should not attempt to do the work  
themselves. SHARP bears no responsibility for  
improper mounting or mounting that results in  
accident or injury.  
CAUTION  
• Attach the stand in the correct direction.  
• Do not remove the stand from the TV unless using an  
optional wall mount bracket to mount it.  
• Be sure to follow the instructions. Incorrect  
installation of the stand may result in the TV falling  
over.  
Using an optional bracket to mount the TV  
Confirm that there are 4 screws supplied with the  
stand unit.  
1
• You can ask a qualified service professional about  
using an optional AN-37AG5 bracket to mount the  
TV to the wall.  
• Carefully read the instructions that come with the  
bracket before beginning work.  
1 Insert the stand into the openings on the bottom  
2
of the TV.  
Hanging on the wall  
AN-37AG5 wall mount bracket.  
(See the bracket instructions for details.)  
• Be sure to attach the stand to the TV with the wider  
side of the base facing forward.  
2 Insert and tighten the 4 screws into the 4 holes  
on the bottom of the stand.  
Soft cushion  
Forward  
1
Vertical mounting  
Angular mounting  
About setting the TV angle  
The center of the display:  
5
0/5/10/15/20°  
/
16  
inch (7.5 mm) under  
Screws  
the “A” position.  
Refer to the operation  
manual of AN-37AG5 for  
details.  
2
• To detach the stand, perform the steps in reverse order.  
• Detach the cable clamp on the rear of the TV when using  
the optional mount bracket.  
• Due to the terminal configuration on this TV, when you  
wall-mount this model, make sure there is enough space  
between the wall and the TV for the cables.  
• To use this TV mounted on a wall, first remove the adhesive  
tape at the 4 locations on the rear of the TV, and then use  
the screws supplied with the wall mount bracket to secure  
the bracket to the rear of the TV.  
7
 
QUICK REFERENCE  
QUICK INSTALLATION TIPS  
Using the Remote Control Unit  
Use the remote control unit by pointing it towards the  
remote control sensor on the TV. Objects between the  
remote control unit and the remote control sensor may  
prevent proper operation.  
Attach your antenna to the back of the television.  
(See page 9.)  
Connect the AC plug for the television into the AC  
outlet.  
1
2
Remote Control sensor  
30º  
17´ (5 m)  
AC outlet  
30º  
30º  
• Place the TV close to the AC outlet, and keep the power  
plug within reach.  
30º  
• TO PREVENT RISK OF ELECTRIC SHOCK, DO NOT  
TOUCH UN-INSULATED PARTS OF ANY CABLES  
WITH THE AC CORD CONNECTED.  
Cautions regarding the remote control unit  
• Do not expose the remote control unit to shock. In addition,  
do not expose the remote control unit to liquids, and do not  
place in an area with high humidity.  
• Do not install or place the remote control unit under direct  
sunlight. The heat may cause deformation of the remote  
control unit.  
How to turn on the television for the first time.  
3
A) Press POWER on the television.  
• The remote control unit may not work properly if the remote  
control sensor on the TV is under direct sunlight or strong  
lighting. In such cases, change the angle of the lighting  
or the TV, or operate the remote control unit closer to the  
remote control sensor.  
POWER  
B) The POWER indicator on the front of the  
television lights GREEN.  
IMPORTANT:  
The POWER indicator on the television should light GREEN  
indicating you have power to the television.  
If the POWER indicator on the television still does not light up,  
press POWER on the remote control to turn the power on.  
IMPORTANT:  
POWER  
indicator  
IF THE UNIT DOES NOT POWER ON - UNPLUG THE  
TELEVISION FROM THE OUTLET AND REPEAT THE  
INSTALLATION STEPS.  
IF YOU STILL ENCOUNTER NO POWER, PLEASE CONTACT  
US AT 1-800-BE-SHARP.  
• Speakers cannot be detached from the TV.  
• TV angle cannot be adjusted.  
8
 
Preparation  
Antennas  
To enjoy a clearer picture, use an outdoor antenna. The following is a brief explanation of the types of connections  
that are used for a coaxial cable. If your outdoor antenna uses a 75-ohm coaxial cable with an F-type connector,  
plug it into the antenna terminal at the rear of the TV set.  
F-type connector  
1. A 75-ohm system is generally a round cable with F-type connector  
that can easily be attached to a terminal without tools (Commercially  
available).  
75-ohm coaxial cable (round)  
2. A 300-ohm system is a flat “twin-lead” cable that can be attached  
to a 75-ohm terminal through a 300/75-ohm adapter (Commercially  
available).  
300-ohm twin-lead cable (flat)  
NOTICE F-type connector should be finger-tightened only.  
F-type connector  
When connecting the RF cable to the TV set, do not tighten F-type  
connector with tools.  
If tools are used, it may cause damage to your TV set. (The breaking  
of internal circuit, etc.)  
75-ohm coaxial cable  
Connecting Antenna Cable  
• Connect the antenna cable to the TV using one of the methods in the illustration as shown (  
,
,
or  
).  
4
1
2
3
Home Antenna  
terminal (75-ohm)  
Cable TV lead-In  
Cable without a CATV  
converter  
1
2
Coaxial cable  
(commercially available)  
VHF/UHF antenna  
Home Antenna  
terminal (75-ohm)  
75-ohm coaxial cable (round)  
Coaxial cable  
(commercially available)  
Combination VHF/  
UHF antenna  
3
4
75-ohm coaxial cable (round)  
300-ohm twin-lead cable (flat)  
or  
300/75-ohm adapter  
(commercially available)  
UHF  
Separate VHF/UHF  
antenna  
300-ohm  
ANTENNA  
twin-lead cable  
VHF  
ANTENNA  
IN  
OUT  
Combiner  
(commercially available)  
300-ohm twin-lead cable  
To TV antenna  
terminal  
or  
75-ohm coaxial cable  
Installing Batteries in the Remote Control Unit  
If the remote control fails to operate TV functions, replace the batteries in the remote control unit.  
1 Open the battery cover.  
2 Insert two “AA” size batteries  
(supplied with the product).  
3 Close the battery cover.  
• Place the batteries with their terminals  
corresponding to the ( ) and (  
indications in the battery compartment.  
)
e
f
CAUTION  
Improper use of batteries can result in chemical leakage or explosion. Be sure to follow the instructions below.  
• Do not mix batteries of different types. Different types of batteries have different characteristics.  
• Do not mix old and new batteries. Mixing old and new batteries can shorten the life of new batteries or cause chemical leakage  
in old batteries.  
• Remove batteries as soon as they are worn out. Chemicals that leak from batteries that come in contact with skin can cause a  
rash. If you find any chemical leakage, wipe thoroughly with a cloth.  
• The batteries supplied with this product may have a shorter life expectancy due to storage conditions.  
• If you will not be using the remote control unit for an extended period of time, remove batteries from it.  
9
 
Part Names  
TV (Front)  
Remote control sensor  
OPC sensor* (See page 18.)  
POWER indicator (See page 12.)  
*OPC: Optical Picture Control  
TV (Rear/Side)  
*2  
*3  
POWER  
button  
MENU  
button  
AC INPUT  
terminal  
INPUT  
button  
*1  
Channel  
buttons  
(CHU/V)  
INPUT 6 terminal  
(HDMI)  
DIGITAL AUDIO  
OUTPUT terminal  
Volume  
buttons  
(VOLk/l)  
AUDIO OUTPUT  
terminals  
*1  
Antenna/Cable in  
INPUT 3  
terminals  
INPUT 1 terminals  
INPUT 2 terminals  
INPUT 4 terminal (PC-IN)  
AUDIO terminal (shared for INPUT 4 and INPUT 5) *4  
INPUT 5 terminal (HDMI)  
SERVICE  
terminal  
*1 See page 11 for external equipment connection.  
*2 See page 17 for button operations.  
*3 See page 8 for connecting the AC cord.  
*4 See page 21 for details on the PC Audio Select function.  
• The illustrations in this operation manual are for explanation purposes and may vary slightly from the actual operations.  
10  
 
Connecting to External Equipment  
You can connect many types of external equipment to your TV like a Blu-ray disc player, DVD player, VCR, Digital  
TV tuner, HDMI equipment, game console or camcorder. To view external source images, select the input source  
from INPUT on the remote control unit or on the TV. (See page 15.)  
CAUTION  
• To protect equipment, always turn off the TV before connecting any external equipment.  
• Please read the relevant operation manual (Blu-ray disc player, etc.) carefully before making connections.  
Connecting a Blu-ray disc player, DVD player, Digital TV STB (Air or Cable), VCR, game console or camcorder  
Terminal on external  
Terminal on the TV  
INPUT 3  
Cable  
equipment  
AV cable (commercially available)  
INPUT 1 or 2  
Component video cable (commercially available)  
Audio cable (commercially available)  
INPUT 2  
S-VIDEO cable (commercially available)  
Audio cable (commercially available)  
*1  
INPUT 5 or 6  
HDMI-certified cable (commercially available)  
Optical fiber cable (commercially available)  
*2  
*3  
DIGITAL AUDIO  
OUTPUT  
*1 • The Component terminals take priority over the S-VIDEO (INPUT 2) terminal.  
*2 • When using an HDMI-DVI conversion cable, input the audio signal to AUDIO terminal of INPUT 5. When you input the audio  
signal via the AUDIO terminal with INPUT 5, set "PC Audio Select" to "Input 5 (HDMI)". (See page 21.)  
*3 • Digital audio can only be output when receiving a digital broadcast.  
Connecting a PC  
Terminal on the TV  
INPUT 4  
Terminal on PC  
Cable  
RGB cable (commercially available)  
Ø 3.5 mm stereo minijack cable (commercially available)  
INPUT 5 or 6  
HDMI-certified cable (commercially available)  
• When connecting a PC to the INPUT 4, set "PC Audio Select" to "Input 4 (PC)". (See page 21.)  
• When connecting a PC to the INPUT 5, set "PC Audio Select" to "Input 5 (HDMI)". (See page 21.)  
• The HDMI terminals only support digital signal.  
• Refer to page 30 for a list of PC signals compatible with the TV.  
11  
 
Watching TV  
Turning On/Off the Power  
Press POWER on the TV or on the remote control unit to turn the  
power on.  
• The POWER indicator (Green): The TV is on. (After a few seconds, a window  
appears with sound.)  
POWER  
• The initial setup starts when the TV powers on for the first time. If the TV has  
been turned on before, the initial setup will not be invoked. For changing the  
settings of the initial setup, perform EZ setup on the Setup menu on page 20.  
Press POWER on the TV or on the remote control unit again to turn the  
power off.  
• The TV enters standby and the image on the screen disappears.  
• The POWER indicator on the TV turns off.  
POWER  
(On/Standby)  
• If you are not going to use this TV for a long period of time, be sure to remove  
the AC cord from the AC outlet.  
Weak electric power is still consumed even when the TV is turned off.  
Initial Setup  
When you turn on the TV for the first time, it will  
automatically memorize the broadcasting channels available  
in the region where you live. Perform the following steps  
before you press POWER on the remote control unit.  
1. Insert the batteries into the remote control unit. (See page 9.)  
2. Connect the antenna cable to the TV. (See page 9.)  
3. Plug in the AC cord to the AC outlet. (See page 8.)  
ENERGY STAR qualification is based on AV MODE "STANDARD".  
Air/Cable (Antenna setting)  
Make sure what kind of connection is made with your TV  
when selecting "Air" or "Cable".  
3
Press  
/
to select "Air" or "Cable", and then  
a b  
press ENTER.  
Language  
TV Location  
Air/Cable  
Air  
Cable  
CH Search  
Language (Language setting)  
Select from among 3 languages: English, French and Spanish.  
CH Search (Channel search)  
Channel auto search makes the TV look for all channels  
viewable in the set area.  
Press  
/
to select the desired language listed on  
a b  
1
the screen, and then press ENTER.  
After “Air/Cable” has been set, “CH Search” is  
highlighted. Press ENTER.  
1
4
Language  
English  
TV Location  
Language  
TV Location  
Air/Cable  
Français  
Air/Cable  
Español  
CH Search  
CH Search  
TV Location  
Select "Home" or "Store" for the location where you plan to  
install the TV. This product qualifies for ENERGY STAR V3.0  
in Home mode default setting.  
Press  
/
to select “Analog & Digital” to search  
2
3
a b  
both analog and digital broadcasts or “Digital”  
to search only digital broadcasts or “Analog” to  
search only analog broadcasts, and then press  
ENTER.  
Press  
/
to select "Home" or "Store", and then  
a b  
2
press ENTER.  
Language  
TV Location  
Air/Cable  
Home  
Store  
Press  
ENTER.  
Analog & Digital  
Digital  
/
to select “Yes”, and then press  
a b  
CH Search  
Yes  
No  
Home: “Power Saving” is set to "Off", and AV MODE is  
set to "STANDARD".  
Analog  
Store: “Power Saving” is set to "Off" and AV MODE is set  
to "DYNAMIC (Fixed)". Picture Reset and Feature Demo  
can be set.  
Picture Reset: AV MODE will be set to "DYNAMIC (Fixed)"  
regardless of whether Picture Reset is "On" or "Off". If you  
select "On", AV MODE will be reset to "DYNAMIC (Fixed)" if  
there is no operation for 30 minutes. When "Off" is selected,  
AV MODE will be set to "DYNAMIC (Fixed)".  
• The Channel search will start automatically.  
• If no channel is found, confirm the type of connection made  
with your TV and try EZ Setup again. (See page 20.)  
• For changing the settings of the initial setup, perform EZ  
setup on the Setup menu on page 20.  
Feature Demo: When “On” is selected, after all the settings are  
completed, the Feature Demo screen is displayed if there is  
no operation for several minutes.  
12  
 
Direct Button Operation  
Changing Volume  
You can change the volume by pressing VOL  
/
on  
k l  
the TV or on the remote control unit.  
• To increase the volume, press VOL  
.
l
k
• To decrease the volume, press VOL  
.
20  
Audio status  
Output Select  
Output device  
Speaker  
Fixed  
Variable  
Variable sound  
Mute  
• When "Output Select" is set to "Variable", the indicator on  
the screen changes as shown below.  
60  
• See page 25 for details on the Output Select function.  
MUTE  
Mutes the current sound output.  
Press MUTE.  
• "  
" will be displayed on the screen for 30 minutes, and  
the sound is silenced.  
POWER  
You can turn on the TV or put it on standby by  
pressing POWER on the TV or on the remote control  
unit. (See page 12.)  
• Within 30 minutes of pressing MUTE, mute can be  
canceled by pressing VOL  
/
or MUTE.  
k l  
• Mute will be canceled after 30 minutes have passed.  
However, the TV will not suddenly output a loud sound as  
the volume level is set to 0 automatically.  
Changing Channels  
You can change channels by pressing CHr/s or  
09, • (DOT).  
Sleep Timer  
Allows you to set a time when the TV automatically  
Examples:  
switches to standby.  
To select a 1 or 2-digit channel number (e. g., Channel 5):  
Press 5  
To select a 3-digit channel number (e. g., Channel 115):  
Press 1 ENT.  
To select a 4-digit channel number (e. g., Channel 22.1):  
Press 2 • (DOT) ENT.  
Press SLEEP.  
• The remaining time displays when the sleep timer has been  
set.  
• Each time you press SLEEP, the remaining time switches  
as shown below.  
ENT.  
1
5
2
1
Off  
30  
60  
90  
120  
• When set, the time automatically starts counting down.  
• If you want to adjust the sleep timer, you can press SLEEP  
twice then change the time setting.  
• When it is 5 minutes before the time expires, the remaining  
time will start to keep appearing every minute.  
• When selecting a 1-digit channel number, it is not necessary  
to press 0 before the number.  
• When you enter 09 only, channel selection will be made if  
there is no operation within a few seconds.  
If you push "0" by itself, nothing will happen.  
• Complete the above steps within a few seconds.  
• When you enter 09 and • (DOT), channel selection will be  
made if there is no operation within a few seconds.  
• Select "Off" by pressing SLEEP to cancel the sleep timer.  
• The TV will enter standby when the remaining time reaches  
0.  
FAVORITE CH  
You can select 4 preset favorite channels in 4 different  
categories.  
Press A, B, C or D.  
• While watching the TV, you can toggle the selected  
channels by pressing A, B, C and D.  
FLASHBACK  
Press FLASHBACK to switch to the previously tuned  
channel.  
• Press FLASHBACK again to switch back to the currently  
tuned channel.  
• See page 26 for details of favorite channel settings.  
• FLASHBACK will not work if no channel has been changed  
after the TV is turned on.  
13  
 
Direct Button Operation  
AV MODE  
AUDIO  
AV MODE gives you several viewing options to choose  
from to best match the surrounding environment of the  
TV, which can vary due to factors like room brightness,  
type of program watched or the type of image input  
from external equipment.  
MTS/SAP stereo mode  
The TV has a feature that allows reception of sound  
other than the main audio for the program. This feature  
is called Multi-channel Television Sound (MTS). The TV  
with MTS can receive mono sound, stereo sound  
and Secondary Audio Programs (SAP). The SAP  
feature allows a TV station to broadcast other  
information, which could be audio in another language  
or something completely different like weather  
information.  
Press AV MODE. Current AV MODE displays.  
• Press AV MODE again before the mode displayed on the  
screen disappears. The mode changes as shown below:  
Example:  
You can enjoy Hi-Fi stereo sound or SAP broadcasts  
where available.  
When the input source is TV, INPUT 1, 2 or 3  
terminals  
STANDARD  
DYNAMIC  
Example:  
• Stereo broadcasts: View programs like live sporting  
events, shows and concerts in dynamic stereo sound.  
• SAP broadcasts: Receive TV broadcasts in either MAIN or  
SAP sound. MAIN sound: The normal program soundtrack  
(either in mono or stereo). SAP sound: Listen to a second  
language, supplementary commentary or other information.  
(SAP is mono sound.)  
MOVIE  
GAME  
USER [TV]  
DYNAMIC (Fixed)  
When the input source is INPUT 4, 5 or 6 terminals  
STANDARD  
MOVIE  
GAME  
PC  
If stereo sound is difficult to hear.  
• Obtain a clearer sound by manually switching to fixed  
mono-sound mode.  
DYNAMIC  
DYNAMIC (Fixed)  
USER[  
]
You can change MTS as shown below to match the television  
broadcast signal.  
STANDARD: For a highly defined image in a normal  
lighting.  
MOVIE: For a movie.  
GAME: Lowers image brightness for easier viewing.  
PC: For PC.  
USER: Allows the user to customize settings as desired.  
You can set the mode for each input source.  
DYNAMIC (Fixed): Changes the image and sound  
settings to the factory preset values. No adjustments  
are allowed.  
DYNAMIC: For a clear-cut image emphasizing high  
contrast, useful for sports viewing.  
Press AUDIO to toggle between audio modes.  
Examples: when receiving MTS and SAP  
STEREO  
MONO  
STEREO mode:  
STEREO + SAP mode:  
ST(SAP) SAP(ST)  
MONO  
MAIN  
SAP  
MAIN + SAP mode:  
MONO mode: MONO  
Digital broadcasting audio mode  
The types of audio transmitted in a digital broadcast  
include SURROUND as well as MONO and STEREO.  
In addition, it is possible for multiple audio tracks to  
accompany a single video track.  
• You can select a different AV MODE item for each input  
mode. (For example, select STANDARD for TV input and  
DYNAMIC for INPUT 1.)  
• When you play games, "GAME" is recommended for AV  
MODE.  
Press AUDIO to toggle between audio modes.  
Example: when receiving Digital broadcasting  
PC  
Audio1: STEREO  
Audio2: STEREO  
Audio3: SURROUND  
Allows you to gain quick access to PC mode.  
Press PC.  
DISPLAY  
• MTS only operates while in TV mode.  
Displays channel information being viewed.  
Press DISPLAY.  
FREEZE  
Allows you to capture and freeze a moving image that  
you are watching.  
Press FREEZE.  
• A moving image is captured.  
• Press FREEZE again to cancel the function.  
• When this function is not available, "No displaying still image  
available." will display.  
• The still image automatically goes out after 30 minutes.  
• If you are using the freeze function and a broadcast  
activates the V-CHIP BLOCK, the freeze function will be  
canceled and a V-CHIP BLOCK message will appear.  
14  
 
Direct Button Operation  
INPUT  
To view external source images, select the input source  
using INPUT on the remote control unit or on the TV.  
Press CC.  
1
2
• This will present the Closed Caption information display.  
Press CC while the Closed Caption information is  
still on the screen.  
• Press repeatedly until you select the desired closed  
caption service.  
Press INPUT.  
• A list of selectable sources appears.  
1
Press INPUT again or press  
input source.  
/
to select the  
a b  
2
Air  
DIGITAL  
An image from the selected source automatically displays.  
• Each time INPUT is pressed, the input source toggles.  
If the corresponding input is not plugged in, you cannot change  
the input. Be sure to connect the equipment beforehand.  
22.1  
Audio1  
Video  
CC  
:
:
:
:
MONO  
1080i (16:9)  
2/5 CC1  
NONE  
Closed Caption  
information  
Ratings  
• See page 11 for external equipment connection.  
• Press PC to switch to an image from the PC.  
• Regardless of whether or not an analog broadcast  
provides Closed Caption service, the closed caption  
display will toggle in the sequence: CC1, CC2, T1, and  
T2.  
• When a digital broadcast provides Closed Caption  
service, the closed caption display will toggle in the  
sequence: DTVCC (actual service), CC1, CC2, T1, and  
T2. CC1, CC2, T1, and T2 are always displayed.  
Operating On-Screen Display Menu  
You can operate the on-screen display menu by using  
the following buttons.  
MENU: Displays the menu screen.  
/
/
/
, ENTER: Select a desired item on the screen.  
a b c d  
RETURN: Returns to the previous menu screen.  
Example:  
EXIT: Turns off the menu screen.  
If a program has three services (DTVCC, CC1 and T1  
(TEXT1)), the closed caption display will toggle in this  
sequence:  
• For operating the on-screen display menu, see “Menu  
Operation Buttons” on page 17.  
1/5 DTVCC1  
2/5 CC1  
3/5 CC2  
4/5 T1  
5/5 T2  
OFF  
Closed Captions and Digital Closed Captions  
• The CC button keeps a record of the last service  
selected in its memory.  
Your TV is equipped with an internal Closed Caption  
decoder. It allows you to view conversations, narration  
and sound effects as subtitles on your TV. Closed  
Captions are available on some TV programs and on  
some VHS home video tapes at the discretion of the  
program provider.  
If the last closed caption mode (e.g. 1/5 DTVCC) you  
selected is not available for the next program, or on  
another channel, the closed caption service that is  
available is automatically selected.  
Closed Caption services that appear in parentheses will  
not be stored in the CC button's memory as your last  
selected service. Only services that you have selected  
with the CC button are stored.  
Digital Closed Caption service is a new caption service  
available only on digital TV programs (also at the  
discretion of the service provider). It is a more flexible  
system than the original Closed Caption system,  
because it allows for a variety of caption sizes and font  
styles. When the Digital Closed Caption service is in  
use, it will be indicated by the appearance of DTVCC.  
Examples:  
In a case where there are two closed caption services  
provided (for instance, DTVCC and CC1), and DTVCC  
is displayed as your current selection, if DTVCC is not  
broadcast for the next program, the other closed caption  
service, CC1, will be displayed.  
Not all programs and VHS videotapes offer closed  
captions. Please look for the “N” symbol to ensure  
that captions will be shown.  
• When “Power Saving” is set to “Standard” or “Advanced”,  
the Power Saving leaf icon appears on the channel  
information window. See page 19 for details of Power  
Saving settings.  
• See page 25 for detailed closed caption settings.  
• When the program contains no closed caption, “--” displays  
in the closed caption information. (Only when receiving a  
digital broadcast.)  
• Four kinds of closed caption service (CC1, CC2, T1 (TEXT1),  
T2 (TEXT2)) are potentially available, but a broadcast  
may contain none or only some of these services at the  
discretion of the program provider.  
In the Closed Caption system, there can be more than  
one caption service provided. Each is identified by its  
own number. The “CC1” and “CC2” services display  
subtitles of TV programs superimposed over the  
program's picture.  
In the Closed Caption system, the “T1 (TEXT1)” or “T2  
(TEXT2)” services display text that is unrelated to the  
program being viewed (e.g., weather or news). These  
services are also superimposed over the program  
currently being viewed.  
15  
 
Direct Button Operation  
VIEW MODE  
You can select the screen size.  
Press VIEW MODE.  
• The View Mode menu displays.  
1
• The menu lists the View Mode options selectable for the type of video signal currently being received.  
Press VIEW MODE or  
/
while the View Mode menu is displayed to select a desired item on the menu.  
a b  
2
• You can sequentially select a View Mode that has its own aspect ratio.  
For 4:3 programs  
Example: Screen size images  
Side Bar  
S.Stretch (Smart stretch)  
Zoom  
Stretch  
Suitable for viewing  
conventional 4:3 programs in programs to fill the screen.  
their normal format.  
Suitable for stretching 4:3  
Suitable for viewing wide-  
screen 2.35:1 anamorphic  
DVDs in full screen.  
This mode is useful for 1.78:1  
DVDs. When viewing 1.85:1  
DVDs, stretch mode will still show  
very thin black bands at the top  
and bottom of the screen.  
For HD programs  
Stretch: Suitable for viewing wide-screen 1.78:1 aspect ratio program, stretch mode will still show very thin black bands at  
the top and bottom of the screen.  
Full Screen: Displays an image faithful to the input signal in full screen.  
S.Stretch (Smart stretch): Suitable for stretching 4:3 programs to fill the screen.  
Zoom: Suitable for viewing wide-screen 2.35:1 aspect-ratio programs in full screen.  
• When using Full Screen, it is possible to see noise or bars around different outer portions of the screen. Please change view  
mode to correct this.  
For PC input mode  
• Connect the PC before making adjustments. (See page 11.)  
• Selectable screen size may vary with input signal type.  
Example: Screen size images  
Input signal  
Normal  
Zoom  
Stretch  
Dot by Dot  
Keeps the original  
aspect ratio in a full  
screen display.  
For viewing  
widescreen  
programs. The top  
and bottom of the  
image is cropped.  
An image fully fills the Detects the resolution  
4:3  
Input signal  
16:9  
screen.  
of the signal and  
displays an image with  
the same number of  
pixels on the screen.  
Stretch  
Dot by Dot  
An image fully fills the Detects the resolution  
screen.  
of the signal and  
displays an image with  
the same number of  
pixels on the screen.  
16  
 
On-Screen Display Menu  
On-Screen Display Menu Operation  
Example  
Example  
Option  
Picture  
Audio Only  
Input Select  
OPC  
[On(Display)]  
Output Select  
Backlight  
Contrast  
Brightness  
Color  
Color System  
[
[
[
[
[
30]  
0
b40  
b30  
b30  
b30  
b20  
Digital Caption Setup  
Digital Caption Info.  
Program Title Display  
Favorite CH  
0] a30  
b2] a30  
0] a30  
Tint  
Sharpness  
Advanced  
Reset  
4]  
0
Operation Lock Out  
Demo Mode  
Identification  
Software Update  
1 Item displayed in yellow  
• This indicates the item currently selected.  
• Press ENTER to go to the adjustment screen for this  
item.  
ENTER  
RETURN  
MENU  
: Exit  
: Select  
: Enter  
: Back  
2 Item displayed in white  
• This indicates that the item can be selected.  
The bar above is an operational guide for  
the remote control. The bar will change in  
accordance with each menu setting screen.  
3 Item displayed in gray  
• This indicates that the item cannot be selected.  
There are various reasons why the items cannot be  
selected, but the main reasons are as follows:  
—Nothing is connected to the selected input terminal.  
—The function is not compatible with the current input  
signal.  
Press MENU to display the MENU screen.  
1
2
1 Press  
/
c d  
to select the desired menu.  
2 Press  
/
a b  
to select a specific adjustment item,  
and then press ENTER.  
3 Press  
/
(or  
/
a b  
c d  
) to select or adjust the  
desired setting, and then press ENTER.  
• Menu options differ in the selected input modes, but the  
operating procedures are the same.  
• The screens in the operation manual are for explanation  
purposes (some are enlarged, others cropped) and may  
vary slightly from the actual screens.  
Press MENU to exit.  
3
Menu Operation Buttons  
Using the remote control  
Use the following buttons on the remote control to  
operate the menu.  
Using the control panel of the main unit  
You can also operate the menu with the control panel  
of the main unit.  
Button operations on the control panel correspond to  
the ones on the remote control as shown below.  
MENU: MENU on the remote  
control.  
INPUT: ENTER on the remote  
control.  
CHU/V: Cursor a/b on the  
MENU:  
Press to open or close the menu screen.  
remote control.  
a/b/c/d: Press to select a desired item on the screen or  
VOLk/l: Cursor c/d on the  
adjust a selected item.  
remote control.  
ENTER:  
Press to go to the next step or complete the  
setting.  
RETURN:  
Press to return to the previous step.  
17  
 
On-Screen Display Menu  
Picture Menu  
Adjusts the picture to your preference with the  
following picture settings.  
Advanced Picture Setting  
This TV provides various advanced functions for  
optimizing the picture quality.  
C.M.S. (Color Management System)  
Example  
Picture  
Color tone is managed using the six-color adjustment  
setting.  
OPC  
[On(Display)]  
C.M.S.-Hue: This is a standard to adjust the color either  
more reddish or more bluish in tone.  
Backlight  
Contrast  
Brightness  
Color  
C.M.S.-Saturation: Increases or decreases the  
saturation of a selected color.  
C.M.S.-Value: A higher value makes the image brighter.  
A lower value makes the image darker.  
[
[
30]  
0
b40  
b30  
b30  
b30  
b20  
0] a30  
[ b2] a30  
Tint  
[
[
0] a30  
Sharpness  
Advanced  
Reset  
4]  
0
• For resetting all adjustment items to the factory preset  
values, press  
ENTER.  
/
to select "Reset", and then press  
a b  
Color Temp. (Color Temperature)  
Selected item  
button  
c
button  
d
Backlight  
The screen dims  
The screen  
brightens  
For more contrast  
For more  
brightness  
For a better white balance, use color temperature  
correction.  
Contrast  
Brightness  
For less contrast  
For less  
brightness  
For less color  
intensity  
High:  
White with bluish tone  
Mid-High:  
Middle:  
Mid-Low:  
Low:  
Color  
For more color  
intensity  
White with reddish tone  
Tint  
Skin tones  
become reddish  
For less  
Skin tones  
become greenish  
For more  
Active Contrast  
Sharpness  
Automatically adjusts the image contrast according to  
the scene.  
sharpness  
sharpness  
On: Automatically adjusts the image contrast.  
Off: No adjustment.  
• For resetting all Picture adjustment items to the factory  
preset values, press to select "Reset", press ENTER,  
press  
/
a b  
/
to select "Yes", and then press ENTER.  
a b  
Film Mode (3:2 pull-down)  
OPC Setting  
Automatically adjusts the brightness of the screen.  
On(Display): Displays the OPC effect on the screen while  
adjusting the brightness of the screen.  
Automatically detects a film-based source (originally  
encoded at 24 frames/second), analyzes it then  
recreates each still film frame for high-definition picture  
quality.  
On: Automatically adjusts.  
Off: The brightness is fixed at the value set in "Backlight".  
On: Detects, analyzes, converts film source.  
Off: Normal viewing mode.  
• "Film Mode" is not selectable when channel display shows  
an input resolution of 480p or 720p.  
• When set to "On", the Optical Picture Control (OPC) senses  
the surrounding light and automatically adjusts the backlight  
brightness. Make sure nothing obstructs the OPC sensor,  
which could affect its ability to sense surrounding light.  
• When set to "On(Display)", OPC effect displays on the  
screen while the OPC adjusts the screen brightness.  
Digital Noise Reduction  
Produces a clearer video image.  
Off: No adjustment  
High/Middle/Low: Select a desired level for viewing a  
clearer video image.  
3D-Y/C  
Provides high quality images with minimal dot crawl  
and cross color noise.  
Slow: For still images.  
Standard: Normal adjustment.  
Fast: For moving images.  
Off: For Game Mode.  
• 3D-Y/C is available for input signal from Composite Video  
and analog broadcasts (air and cable).  
18  
 
On-Screen Display Menu  
Monochrome  
Bass Enhancer  
For viewing a video in monochrome.  
On: For viewing in monochrome.  
Off: Normal color.  
This function allows you to enjoy bass-enhanced sound.  
On: Bass Enhancer function is on.  
Off: Normal sound.  
Range of OPC  
• Audio menu is grayed out when Output Select is set to  
"Variable". (See page 25.)  
The brightness level range of the OPC sensor's  
automatic adjustments can be set according to your  
preferences.  
Power Control Menu  
Power control setting allows you to save energy.  
The adjustment range of the OPC sensor can be set to  
a maximum of +16 and a minimum of –16.  
Max.: –15 through +16  
Min.: –16 through +15  
Example  
Power Control  
• The maximum setting cannot be set to a smaller number  
than the minimum setting.  
• The minimum setting cannot be set to a bigger number  
than the maximum setting.  
Power Saving  
No Signal Off  
No Operation Off  
• Depending on the brightness of the surrounding light, the  
OPC sensor might not operate if the adjustment range is  
small.  
Power Saving  
This function allows you to automatically reduce the  
backlight brightness in order to decrease the power  
consumption and increase the backlight lifespan.  
Standard: Reduces the backlight brightness to 80%.  
Audio Menu  
You can adjust the sound quality to your preference  
with the following settings.  
When set to “Standard”, “ ” appears on the screen.  
Advanced: Reduces the backlight brightness to 70%.  
Example  
Audio  
When set to “Advanced”, “  
screen.  
” appears on the  
Off: The backlight brightness is the same value of your  
Treble  
[
[
[
0]  
0]  
0]  
a15  
a15  
L
b15  
b15  
R
settings in the selected AV MODE.  
Bass  
Balance  
Surround  
• “Power Saving” does not function when you set “AV MODE”  
to “DYNAMIC (Fixed)”.  
• When “OPC” is set to “On(Display)” or “On” while “Power  
Saving” is set to “Standard” or “Advanced”, the Power  
Saving leaf icon appears to the left of “OPC” in the Picture  
menu screen.  
Bass Enhancer  
Reset  
• When “OPC” is set to “Off” while “Power Saving” is set  
to “Standard” or “Advanced”, the Power Saving leaf icon  
appears to the left of “Backlight” in the Picture menu  
screen.  
Selected item  
Treble  
button  
button  
d
c
For weaker treble For stronger treble  
Bass  
For weaker bass  
For stronger bass  
Balance  
Decrease audio  
from the right  
speaker  
Decrease audio  
from the left  
speaker  
No Signal Off  
When set to "Enable", the power will automatically shut  
down if there is no signal for 15 minutes.  
• Audio menu is grayed out when Output Select is set to  
"Variable". (See page 25.)  
• For resetting all Audio adjustment items to the factory  
• When it is 5 minutes before the power shuts down, the  
remaining time will start to keep appearing every minute.  
• "Disable" is the factory preset value.  
preset values, press  
/
to select "Reset", press ENTER,  
a b  
press  
/
to select "Yes", and then press ENTER.  
a b  
• When a TV program finishes, this function may not operate.  
Surround  
No Operation Off  
Surround function allows you to enjoy realistic "live"  
You can set the time length the TV takes to automatically  
shut the power down when there is no operation.  
30min/3Hour/Disable  
sound.  
On: Surround function is on.  
Off: Normal sound.  
• When it is 5 minutes before the power shuts down, the  
remaining time will start to keep appearing every minute.  
• "Disable" is the factory preset value.  
• Audio menu is grayed out when Output Select is set to  
"Variable". (See page 25.)  
• For some discs, setup may be required on your DVD player.  
In this case, please refer to the operation manual of your  
DVD player.  
19  
 
On-Screen Display Menu  
Setup Menu  
CH Setup  
If initial setup does not memorize all the channels in  
your region, follow the instructions below to manually  
memorize the channels.  
Example  
Setup  
Air/Cable: Make sure what kind of connection is made  
with your TV when selecting "Air" or "Cable".  
CH Search: Channel auto search makes the TV look for  
all channels viewable in the set area.  
EZ Setup  
CH Setup  
Input Skip  
Input Label  
Parental CTRL  
Position  
CH Memory: You can select the channels to skip in each  
ANALOG (Air), ANALOG (Cable), DIGITAL (Air) and  
DIGITAL (Cable).  
On: Skips channels. (Channel selection disabled using CH  
r s  
/
.)  
Off: Does not skip channels. (Channel selection enabled using  
r
CH  
s
/ .)  
PC Setup  
Antenna Setup Digital: In order to receive digital air  
broadcasts, you need a digital broadcast antenna.  
You can confirm the antenna configuration through the  
"Antenna Setup Digital" screen. If necessary, adjust the  
direction of the antenna to obtain the maximum signal  
strength.  
Signal Strength: The signal strength of DIGITAL channel is  
displayed. The signal information is based on the current  
channel.  
PC Audio Select  
HDMI Auto View  
Audio Setup  
Language  
Reset  
Channel Strength: Input the 2-digit channel number to check  
the signal strength of the selected channel. Make sure the  
signal is strong enough for each channel.  
EZ Setup  
This function is available for DIGITAL (Air) only.  
You can run EZ Setup again, even after setting up the  
preset channels.  
Language: Select from among 3 languages (English,  
French and Spanish).  
• See "Initial Setup" on page 12 for setting each item.  
• If no channel is found, confirm the type of connection made  
with your TV and try channel search again.  
TV Location: Select "Home" or "Store" for the location  
where you plan to install the TV. This product qualifies  
for ENERGY STAR V3.0 in Home mode default setting.  
Home: “Power Saving” is set to "Off", and AV MODE is set to  
"STANDARD".  
Input Skip  
This setting allows you to skip the HDMI or PC-IN Input  
("Input 4 (PC)", "Input 5 (HDMI)" and "Input 6 (HDMI)"  
on the Input Selection operation.  
Store: “Power Saving” is set to "Off" and AV MODE is set to  
"DYNAMIC (Fixed)". Picture Reset and Feature Demo can  
be set.  
Picture Reset: AV MODE will be set to "DYNAMIC (Fixed)"  
regardless of whether Picture Reset is "On" or "Off". If  
you select "On", AV MODE will be reset to "DYNAMIC  
(Fixed)" if there is no operation for 30 minutes. When "Off"  
is selected, AV MODE will be set to "DYNAMIC (Fixed)".  
Feature Demo: When “On” is selected, after all the settings  
are completed, the Feature Demo screen is displayed if  
there is no operation for several minutes.  
Yes: Skips the input.  
No: Does not skip input.  
Input Label  
Lets you set the input terminal displayed when using  
the INPUT SOURCE menu or channel display. Press  
/
/
/
to select the new name for the input  
a b c d  
• ENERGY STAR qualification is based on AV MODE  
"STANDARD".  
mode.  
Air/Cable: Make sure what kind of connection is made  
with your TV when selecting "Air" or "Cable".  
CH Search: Channel auto search makes the TV look for  
all channels viewable in the set area.  
• You cannot change labels if the INPUT SOURCE is TV.  
• See "Initial Setup" on page 12 for setting each item.  
• If no channel is found, confirm the type of connection made  
with your TV and try EZ Setup again.  
20  
 
On-Screen Display Menu  
Position  
Fine Sync.  
Ordinarily you can easily adjust the picture as  
necessary to change image position using Auto Sync.  
In some cases, however, manual adjustment is needed  
to optimize the image.  
For adjusting a picture's horizontal and vertical  
position.  
H-Pos.: Centers the image by moving it to the left or  
right.  
V-Pos.: Centers the image by moving it up or down.  
H-Pos.: Centers the image by moving it to the left or  
right.  
V-Pos.: Centers the image by moving it up or down.  
Clock: Adjust when the image flickers with vertical  
stripes.  
Phase: Adjust when characters have low contrast or  
when the image flickers.  
• For resetting adjustments to the factory preset values, press  
/
to select "Reset", and then press ENTER.  
a b  
• When connecting a PC to the HDMI terminal, the image  
position will be automatically adjusted. It cannot be  
manually adjusted.  
• Adjustments are stored separately according to input  
source.  
• When a DTV channel is selected, the horizontal position  
cannot be adjusted.  
• The horizontal and/or vertical position may not be able to  
be adjusted or it may be adjusted only to a certain degree.  
• For resetting all Fine Sync. adjustment items to the factory  
preset values, press  
ENTER.  
/
to select "Reset", and then press  
a b  
• It is not necessary to adjust the "Clock" or "Phase" when a  
digital signal is being input, so it cannot be selected.  
• The default cursor position may not be in the center,  
because the screen position variable ranges may be  
asymmetrical.  
PC Setup  
Input Signal (for Analog PC Input Mode Only)  
PC Audio Select  
Some input signals may have to be registered manually  
to display properly. The pair of input signals (resolutions)  
in the list below is not distinguishable when received.  
In such a case, you have to set the correct signal  
manually. After setting once, it will display when the  
same signal (resolution) is input again.  
Determines whether the AUDIO terminal is used for  
INPUT 4 (PC-IN) or INPUT 5 (HDMI).  
Input 4 (PC): Select this item when the audio signal is  
input via the INPUT 4 (PC-IN) terminal using an analog  
RGB cable.  
Input 5 (HDMI): Select this item when the audio signal is  
input via the INPUT 5 (HDMI) terminal using an HDMI-  
DVI conversion cable.  
1024 x 768  
1360 x 768  
• You can only select the "Input Signal" on the Setup menu  
when receiving one of the 2 input signals listed above.  
• When "PC Audio Select" is set to "Input 5 (HDMI)", sound  
will not be produced if you use only an HDMI-certified  
cable to connect HDMI-compatible equipment. To produce  
sound, you should make an analog audio connection.  
• If you want to connect HDMI-compatible equipment using  
only an HDMI-certified cable, set "PC Audio Select" to  
"Input 4 (PC)".  
Auto Sync. (for Analog PC Input Mode Only)  
For automatically adjusting the PC image.  
Yes: Auto Sync. starts.  
No: This function does not work.  
HDMI Auto View  
To watch an HDMI or PC-IN equipment image, select  
"INPUT5" or "INPUT6" from "INPUT SOURCE" menu  
using INPUT on the remote control unit or on the TV.  
Enable: To use View Mode based on signal recognition,  
including an HDMI signal.  
• When Auto Sync. is successful, "Completed" displays. If  
not, Auto Sync. failed.  
• Auto Sync. may fail even if "Completed" displays.  
• Auto Sync. may fail if the computer image has low  
resolution, has unclear (black) edges, or is moved while  
executing Auto Sync.  
Disable: No function.  
• Be sure to connect the PC to the TV and switch it on before  
starting Auto Sync.  
• Refer to your external equipment operation manual for the  
signal type.  
• When connecting an HDMI-DVI conversion adapter/cable  
to the HDMI terminal, the image may not come in clearly.  
21  
 
On-Screen Display Menu  
Audio Setup  
You can output digital audio to an AV amplifier or  
similar device whose DIGITAL AUDIO INPUT terminal  
is connected to the DIGITAL AUDIO OUTPUT terminal  
on the TV. Please select an audio output format  
compatible with the audio format of the program you  
are watching and the equipment connected.  
PCM: The optical output terminal outputs audio signal  
in PCM form. If your digital audio system does not  
support Dolby Digital, select "PCM".  
New Secret No.  
You can set and change the secret number by using  
09.  
Input Secret No.: When you change the secret number,  
enter the old 4-digit secret number here. The cursor  
moves to "New Secret No.".  
New Secret No.: When you set the new secret number,  
enter the new 4-digit secret number here. The cursor  
moves to "Reconfirm".  
Reconfirm: Enter the same 4-digit number you set in  
"New Secret No.".  
Dolby Digital: The optical output terminal outputs audio  
signal in Dolby Digital form. It reproduces sound from  
surround program of digital.  
Secret No. Clear  
You can clear your secret number.  
Yes: Your secret number is cleared.  
No: Your secret number is not cleared.  
Language  
You can also select a language from the Setup menu.  
Select from among 3 languages: English, French and  
Spanish.  
• As a precautionary measure, make a note of your secret  
number and keep it in a familiar place.  
• If the secret number is cleared, the Status setting  
automatically sets to "Off". "V-Chip" and "Status" will not be  
selectable from the menu.  
Reset  
If complex adjustments are made and the settings  
cannot be restored to normal, you can reset the  
settings to the factory preset values.  
"Return to factory pre-setting" displays on the  
screen.  
• If you have already set the Secret No., input the 4-digit  
secret number here.  
Select "Yes".  
• After the reset has been completed, the power shuts off  
and then comes back on. The screen will have returned  
to its original settings.  
Status  
1
Used to enable or disable the parental control function.  
This function will not be selectable from the menu if  
you do not first configure your secret number.  
On: Enables Parental CTRL.  
2
Off: Disables Parental CTRL.  
V-Chip  
V-CHIP is an electronic filtering device built into your  
TV. This tool gives parents a great degree of control  
over broadcasts accessed by their children. It allows  
parents to select programs judged suitable for child  
viewing while blocking ones judged not suitable. It  
does so automatically once you activate the V-CHIP  
feature in your TV. "V-Chip" and "Status" will not be  
selectable from the menu if you do not first configure  
your secret number.  
• The Channel Setup settings will not be changed.  
• The Language settings will not be changed.  
• The Secret number settings will not be changed.  
• The TV Location settings will not be changed.  
Parental CTRL  
(Parental Control Setting)  
• The U.S. has two rating systems for viewing content: TV  
Parental Guidelines and movie ratings.  
Secret No.  
• The TV Parental Guidelines work in conjunction with the  
V-CHIP to help parents screen out inappropriate television  
shows from their children.  
Allows you to use a secret number to protect certain  
settings from being accidentally changed.  
• Movie ratings are used for original movies rated by the  
Motion Picture Association of America (MPAA) as watched  
on cable TV and not edited for television. The V-CHIP can  
also be set to block MPAA-rated movies.  
IMPORTANT:  
Three conditions must be met to enable the V-Chip (see  
pages 22 to 24):  
1.Secret No. is registered.  
2.V-Chip/V-Chip (DTV Only) settings have been made.  
• The “V-Chip (DTV Only)” will only be selectable when  
a new rating system can be downloaded via digital  
broadcasting in the U.S.  
• The setting automatically enters "Block" for any ratings  
below your selection.  
• If Status is not set to "On", the configuration settings will not  
work.  
3."Status" is set to "On".  
22  
 
On-Screen Display Menu  
G: General audiences. All ages admitted.  
PG: Parental guidance suggested. Some material may not be  
suitable for children.  
PG-13: Parents strongly cautioned. Some material may be  
inappropriate for children under 13.  
R: Restricted. Under 17 requires accompanying parent or  
adult guardian (age varies in some jurisdictions).  
NC-17: No one 17 and under admitted.  
MPAA (Voluntary movie rating system)  
Example  
MPAA  
TV Guidelines  
G
-----  
-----  
Can. English Ratings  
Can. French Ratings  
PG  
PG-13  
R
-----  
Block  
Block  
Block  
X: X is an older rating that is unified with NC-17 but may be  
encoded in the data of older movies.  
NC-17  
X
NONE  
Press  
/
to adjust the item to your desired position.  
a b  
"Block" indicates the item is blocked. Press MENU to  
exit.  
• Voluntary movie rating system only uses an age-based  
rating.  
TV Parental Guidelines  
Press to adjust the item to your desired position.  
"Block" indicates the item is blocked. Press MENU to exit.  
/
a b  
Example  
MPAA  
TV Guidelines  
D
L
Block  
Block  
Block  
Block  
TV-Y  
-----  
-----  
Can. English Ratings  
Can. French Ratings  
TV-Y7  
TV-G  
-----  
S
V
TV-PG  
Block  
FV -----  
TV-14  
TV-MA  
NONE  
Block  
Block  
Example  
When setting an individual content-based rating  
item:  
MPAA  
Press  
or ENTER to access blocked content  
d
TV Guidelines  
D
L
Block  
Block  
Block  
-----  
1
2
3
TV-Y  
-----  
-----  
items from the currently selected age-based rating  
item.  
Can. English Ratings  
Can. French Ratings  
TV-Y7  
TV-G  
S
V
-----  
TV-PG  
TV-14  
TV-MA  
NONE  
-----  
Press to select an individual item, and then  
/
a b  
FV -----  
Block  
Block  
press ENTER to unblock it ("Block" is removed).  
Repeat the same steps for the other items.  
Press  
or RETURN to register after all individual  
c
content rating items are set.  
Content  
FV  
V
S
L
D
Rating  
(Fantasy (Violence)  
violence)  
(Sexual  
(Adult  
(Sexually  
situation) language) suggestive  
dialog)  
TV-Y (All children)  
TV-Y7 (Directed to older children)  
TV-G (General audience)  
Suggested  
age  
TV-PG (Parental Guidance suggested)  
TV-14 (Parents strongly cautioned)  
TV-MA (Mature audience only)  
: The content rating can be set, but this rating is not normally broadcast by TV stations.  
: Content rating can be set.  
23  
 
On-Screen Display Menu  
Canadian Rating Systems (Canadian English ratings and Canadian French ratings)  
• The TV rating systems in Canada are based on the Canadian Radio-Television and Telecommunications Commission (CRTC)  
policy on violence in television programming.  
• While violence is the most important content element to be rated, the structure developed takes into consideration other  
program content like language, nudity, sexuality and mature themes.  
• When setting the V-CHIP on the Canadian system you can choose either the Canadian English ratings or the Canadian French  
ratings.  
E: Exempt: Includes news, sports, documentaries and other information  
programming; talk shows, music videos, and variety programming.  
C: Children: Intended for younger children under the age of 8 years.  
Pays careful attention to themes that could threaten their sense of  
security and well-being.  
C8+: Children over 8 years old: Contains no portrayal of violence as the  
preferred, acceptable, or only way to resolve conflict; nor encourage  
children to imitate dangerous acts which they may see on the screen.  
G: General: Considered acceptable for all age groups. Appropriate  
viewing for the entire family, contains very little violence, physical,  
verbal or emotional.  
PG: Parental Guidance: Intended for a general audience, but may not  
be suitable for younger children (under the age of 8) because it could  
contain controversial themes or issues.  
14+: Over 14 years: Could contain themes where violence is one of  
the dominant elements of the storyline, but it must be integral to the  
development of plot or character. Language usage could be profane  
and nudity present within the context of the theme.  
Canadian English Ratings  
Example  
MPAA  
E
-----  
-----  
TV Guidelines  
C
Can. English Ratings  
Can. French Ratings  
C8+  
G
-----  
Block  
Block  
Block  
Block  
PG  
14+  
18+  
NONE  
Press  
/
to adjust the item to your desired  
a b  
position. "Block" indicates the item is blocked.  
Press MENU to exit.  
18+: Adults: Intended for viewers 18 years and older and might contain  
depictions of violence, which while related to the development of plot,  
character or themes, are intended for adult viewing. Could contain  
graphic language and portrayals of sex and nudity.  
Canadian French Ratings  
E: Exempt programming.  
G: General: All ages and children, contains minimal direct violence, but  
may be integrated into the plot in a humorous or unrealistic manner.  
8ans+: General but inadvisable for young children: May be viewed  
by a wide public audience, but could contain scenes disturbing to  
children under 8 who cannot distinguish between imaginary and real  
situations.  
Example  
MPAA  
TV Guidelines  
E
-----  
-----  
Can. English Ratings  
Can. French Ratings  
G
8ans+  
13ans+  
16ans+  
18ans+  
NONE  
Block  
Block  
Block  
Block  
Recommended for viewing with parent.  
13ans+: Over 13 years: Could contain scenes of frequent violent scenes  
and therefore recommended for viewing with parent.  
16ans+: Over 16 years: Could contain frequent violent scenes and  
intense violence.  
18ans+: Over 18 years: Only for adult viewing. Could contain frequent  
violent scenes and extreme violence.  
Press  
/
to adjust the item to your desired  
a b  
position. "Block" indicates the item is blocked.  
Press MENU to exit.  
How to temporarily release the V-CHIP BLOCK  
When the V-CHIP BLOCK is working and censors a broadcast, "V-CHIP HAS BEEN ACTIVATED." displays.  
Press ENTER while the V-CHIP is working, and then the secret number setting menu displays.  
Input the 4-digit secret number by using 09. At this time V-CHIP BLOCK temporarily releases.  
1
2
Reactivating the temporarily released V-CHIP BLOCK  
You can reactivate the temporarily released V-CHIP BLOCK as shown below.  
• Select "Status" setting from the Parental CTRL menu to reactivate BLOCK. (See page 22.)  
• Select "V-Chip" setting ("MPAA", "TV Guidelines", "Can. English Ratings" or "Can. French Ratings") from the Parental CTRL to  
reactivate BLOCK. (See pages 22 to 24.)  
• Switch off the TV power.  
• Performing any of the three above will activate the V-CHIP BLOCK.  
24  
 
On-Screen Display Menu  
Option Menu  
Output Select  
Allows you to select what controls the audio output.  
Fixed: Sound via speaker is adjusted with VOL  
/
on  
k l  
Example  
Option  
the remote control unit or VOL  
/
on the TV.  
k l  
Sound via the AUDIO OUTPUT terminal is not  
adjustable and outputs at a consistent level.  
Variable: Sound via the AUDIO OUTPUT terminal is  
Audio Only  
Input Select  
adjusted with VOL  
/
on the remote control unit or  
k l  
Output Select  
VOL  
/
on the TV.  
k l  
Color System  
Sound via speaker is muted.  
Digital Caption Setup  
Digital Caption Info.  
Program Title Display  
Favorite CH  
Color System  
Select the video signal system compatible with your  
equipment from the list below:  
Auto/NTSC/PAL-M/PAL-N  
Operation Lock Out  
Demo Mode  
• "Color System" can only be set for the INPUT 2 S-VIDEO  
and INPUT 3 VIDEO.  
• If you have already set the Secret No., input the 4-digit  
secret number here. See page 22 for setting a secret  
number.  
Identification  
Software Update  
Audio Only  
Digital Caption Setup  
When listening to music from a music program, you  
can turn the screen off and enjoy audio only.  
On: Audio is output without screen image.  
This function allows you to adjust the closed caption  
screen appearance to suit your preference. You can  
adjust 8 items: “Font Size”, “Font Style”, “Font Color”,  
“Font Opacity”, “Background Color”, “Background  
Opacity”, “Font Edge” and “Edge Color”.  
Off: Both screen images and audio are output.  
• The screen image will return to normal when a button (except  
those for audio adjustment, such as VOL, MUTE, AUDIO)  
is pressed.  
Example:  
Selectable items available for "Font Style".  
Default: The font specified by broadcasting station or  
default font.  
Type 0: Proportional font used in the MENU screen.  
Type 1: Monospaced with serifs.  
Type 2: Proportionally spaced with serifs.  
Type 3: Monospaced without serifs.  
Type 4: Proportionally spaced without serifs.  
Type 5: Casual font type.  
Input Select  
If the image does not come in clearly from the external  
equipment connected to INPUT 2, you may need to  
change the input signal type setting from the list below:  
Auto/COMPONENT/S-TERMINAL  
Type 6: Cursive font type.  
Type 7: Small capitals.  
• If the selected signal type is incorrect, images are not  
displayed at all or are displayed without any color.  
• Refer to your external equipment operation manual for the  
signal type.  
• If you set INPUT 2 to Auto, the TV will automatically select  
the input signal.  
• For resetting adjustments to the factory preset values, press  
/
to select "Reset", and then press ENTER.  
a b  
• The default value depends on the broadcasting station.  
• Setting INPUT 2 signal selection to "Auto" when other  
equipment is connected will result in the following  
connection priority.  
Digital Caption Info.  
(Digital Caption Information)  
This function allows viewing of digital closed caption  
information for the digital broadcast program being  
viewed.  
INPUT 2:  
COMPONENT VIDEO  
S-VIDEO  
1
2
• This list is not displayed for analog broadcasts or external  
input audio/video.  
• This information is not included in CC1, CC2, T1 (TEXT1),  
or T2 (TEXT2), and is not displayed in a list.  
Program Title Display  
Select the CH display when changing channels for  
digital broadcasting.  
On: "Program Info." displays.  
Off: "Program Info." does not display.  
25  
 
On-Screen Display Menu  
Favorite CH  
Software Update  
(Favorite Channel Setting)  
This function allows software updates by inserting  
a USB memory device with the update file into the  
SERVICE terminal on the TV.  
To check for the availability of a software update, visit  
call 1-800-BE-SHARP (800-237-4277).  
This function allows you to program 4 favorite  
channels, in 4 different categories. By setting the  
favorite channels in advance, you can select your  
favorite channels easily.  
To register your favorite channel:  
Select "Register" and then press ENTER. Press  
/
/
/
a b c  
CAUTION  
to select the position in the category, and then press  
ENTER to register.  
d
• Do not remove the USB memory device or unplug the  
AC cord while the software is being updated.  
• Be sure to properly follow the whole procedure  
described below, step by step. Otherwise, for  
example, the TV cannot read the data in the USB  
memory device and software updating will fail.  
To delete your favorite channel:  
Select "1 Data Clear" and then press ENTER. Press  
/
/
/
to select the channel you want to delete, and  
a b c d  
then press ENTER. Select "Yes" and then press ENTER.  
To delete all the favorite channels, select "All Data Clear".  
Insert the USB memory device with the update file  
into the SERVICE terminal on the TV.  
1
• Before setting the channel, select the channel you want to  
register as a favorite channel.  
Operation Lock Out  
This function locks the operation buttons on the TV  
and the remote control.  
Off: No adjustment.  
RC Control Lock: All buttons on the remote control are  
locked.  
Button Control Lock: All buttons on the TV, except  
POWER, are locked.  
• To unlock the buttons on the remote control, press MENU  
on the TV, and then select "Off" on the MENU screen.  
• To unlock the buttons on the TV, press MENU on the  
remote control, and then select "Off" on the MENU screen.  
Press MENU to display the MENU screen, and then  
2
3
press  
Press  
/
to select “Option”.  
c d  
/
to select “Software Update”, and then  
a b  
press ENTER.  
Demo Mode  
• If you have already set the Secret No., go to step 4.  
Select to play the Demo Mode.  
On: Play product feature demos continuously.  
Off: This function does not work.  
Option  
Audio Only  
• If the power is turned off or the AC cord is unplugged when  
the TV is in demo mode, the TV will start in demo mode  
when it is turned back on.  
Demo Mode  
Identification  
Software Update  
Identification  
The current version of the TV software is displayed.  
Input the 4-digit secret number by using 09.  
4
5
Please enter password.  
Press ENTER to start checking the data in the USB  
memory device.  
Insert the USB memory device containing  
the software update file.  
Use SERVICE port near the INPUT3.  
OK  
26  
 
On-Screen Display Menu  
During the data checking, “Checking” blinks.  
Press ENTER to start updating.  
6
7
• The screen becomes dark for a while until the update  
screen can be displayed. Please wait for the update  
screen to appear. Do not unplug the AC cord.  
Now checking the data in the USB memory device.  
The picture will temporarily go dark until  
the Software Update display appears.  
Wait several minutes and do not unplug the AC cord.  
Checking  
• The current version of the TV software and the version  
of the update file on the USB memory device are  
displayed. To update the TV software with the update  
file, select “Yes”, and then press ENTER.  
OK  
Example  
Example  
Software update file is detected  
in the USB memory device.  
Start update?  
Now updating  
Do not unplug AC cord.  
Update Version  
UXXXXXX2  
Current Version:  
Update Version:  
UXXXXXX1  
UXXXXXX2  
30%  
Yes  
No  
CAUTION  
• If the USB memory device is not properly installed or the  
correct update file cannot be found on the USB memory  
device, an error message is displayed.  
• Do not remove the USB memory device or unplug the  
AC cord while the software is being updated.  
• Check the file on the USB memory device, and then  
reinsert the USB memory device correctly.  
When the software is successfully updated, a  
8
screen is displayed indicating that the update  
process is completed.  
Software update file is not detected  
in the USB memory device.  
Confirm that you have transferred the file  
to the USB memory device and retry software update.  
Confirm that you have inserted the USB memory device  
into the SERVICE port near the INPUT3.  
After this screen is displayed, the TV automatically  
turns off and then turns on again.  
Example  
OK  
Software update is complete.  
There is more than one software file  
in the USB memory device.  
Update Version  
UXXXXXX2  
Confirm that only the software update file is  
in the USB memory device.  
• If the update has failed, check the file in the USB  
memory device and try Software Update again.  
OK  
Failed to complete update.  
Retry Software Update.  
If system Update fails again,  
contact the customer service center.  
After the screen shown below is displayed, press  
ENTER.  
9
System software was  
successfully updated.  
Remove the USB memory device.  
OK  
Remove the USB memory device.  
10  
27  
 
Appendix  
Troubleshooting  
Problem  
Possible Solution  
• No power  
• Check if you pressed POWER on the remote control unit. (See page 12.) If the  
indicator on the TV does not light up, press POWER on the TV.  
• Is the AC cord disconnected? (See page 8.)  
• Has the power been turned on? (See page 12.)  
• Unit cannot be operated.  
• External influences such as lightning, static electricity, may cause improper  
operation. In this case, operate the unit after first turning off the power of the TV or  
unplugging the AC cord and replugging it in after 1 or 2 minutes.  
• Remote control unit does not  
operate.  
• Are batteries inserted with polarity (  
,
) aligned? (See page 9.)  
f
e
• Are batteries worn out? (Replace with new batteries.)  
• Are you using it under strong or fluorescent lighting?  
• Is a fluorescent light illuminated near the remote control sensor?  
• Picture is cut off/with sidebar  
screen.  
• Is the image position correct? (See page 21.)  
• Are screen mode adjustments such as picture size made correctly? (See page 16.)  
• Strange color, light color, or color • Adjust the picture tone. (See pages 18 and 19.)  
misalignment  
• Is the room too bright? The picture may look dark in a room that is too bright.  
• Check the input signal setting. (See page 21.)  
• Power is suddenly turned off.  
• Is the sleep timer set? (See page 13.)  
• Check the power control settings. (See page 19.)  
• The unit's internal temperature has increased. Remove any objects blocking vent or  
clean.  
• No picture  
• Is connection to other components correct? (See page 11.)  
• Is correct input signal source selected after connection? (See page 25.)  
• Is the correct input selected? (See page 25.)  
• Is picture adjustment correct? (See pages 18 and 19.)  
• Is “On” selected in “Audio Only”? (See page 25.)  
• Is a non-compatible signal being input? (See page 30.)  
• No sound  
• Is the volume too low? (See page 13.)  
• Is “Variable” selected in “Output Select”? (See page 25.)  
• Have you pressed MUTE on the remote control unit? (See page 13.)  
• The TV sometimes makes a  
cracking sound.  
• This is not a malfunction. This happens when the cabinet slightly expands and  
contracts according to change in temperature. This does not affect the TV's  
performance.  
Troubleshooting-Digital Broadcasting  
The error message about reception of broadcast  
The example of an error message  
displayed on a screen  
Possible Solution  
• Failed to receive broadcast.  
• No broadcast now.  
• Check the antenna cable. Check that the antenna is correctly setup.  
• Check the broadcast time in the program guide.  
Cautions regarding use in high and low temperature environments  
• When the unit is used in a low temperature space (e.g. room, office), the picture may leave trails or appear slightly delayed.  
This is not a malfunction, and the unit will recover when the temperature returns to normal.  
• Do not leave the unit in a hot or cold location. Also, do not leave the unit in a location exposed to direct sunlight or near a  
heater, as this may cause the cabinet to deform and the Liquid Crystal panel to malfunction. Storage temperature: 4°F to  
f
140°F ( 20°C to 60°C)  
e
f
e
28  
 
Appendix  
Specifications  
Item  
LCD panel  
Model: LC-32SB27U  
32o Class (31 1/2o Diagonal)  
Advanced Super View & BLACK TFT LCD  
Resolution  
1,049,088 pixels (1,366 g 768)  
TV-standard (CCIR)  
VHF/UHF  
American TV Standard ATSC/NTSC System  
VHF 2-13ch, UHF 14-69ch  
CATV  
1-135ch (non-scrambled channel only)  
TV  
Function  
Receiving  
Channel  
Digital Terrestrial  
Broadcast (8VSB)  
2-69ch  
Digital cable*1  
(64/256 QAM)  
1-135ch (non-scrambled channel only)  
Audio multiplex  
BTSC System  
Backlight  
Audio out  
60,000 hours (at Backlight Standard position)  
10W g 2  
INPUT 1  
INPUT 2  
COMPONENT in  
COMPONENT in, S-VIDEO in  
INPUT 4  
ANALOG RGB (PC) in (15-pin mini D-sub female connector), Audio in (Ø 3.5 mm jack)  
HDMI in with HDCP, Audio in (Ø 3.5 mm jack)  
HDMI in with HDCP  
INPUT 5  
Rear INPUT 6  
ANT/CABLE  
AUDIO  
75 q Unbalance, F Type g 1 for Analog (VHF/UHF/CATV) and Digital (AIR/CABLE)  
Audio in (Ø 3.5 mm jack)  
Terminals  
DIGITAL AUDIO OUTPUT Optical Digital audio output g 1 (PCM/Dolby Digital)  
OUTPUT  
INPUT 3  
SERVICE  
Audio out  
AV in  
Side  
Software update  
English/French/Spanish  
AC 120 V, 60 Hz  
125 W (0.3 W Standby with AC 120V)  
28.7 lbs./13.0 kg  
26.5 lbs./12.0 kg  
OSD language  
Power Requirement  
Power Consumption  
TV + stand  
TV only  
Weight  
TV + stand  
TV only  
31 47  
31 47  
/
/
64 g 22 61  
/
64 g 9 49  
/64 inch  
Dimension*2  
(W g H g D)  
64 g 21 1 32 g 4 11  
/
/
64 inch  
Operating temperature  
e32°F to e104°F (0°C to e40°C)  
*1 Emergency alert messages via Cable are unreceivable.  
*2 The dimensional drawings are shown on the Spanish operation manual.  
• As part of policy of continuous improvement, SHARP reserves the right to make design and specification changes for product  
improvement without prior notice. The performance specification figures indicated are nominal values of production units.  
There may be some deviations from these values in individual units.  
Part name  
Model number  
Optional Accessory  
Wall mount bracket  
AN-37AG5  
The listed optional accessory is available for the Liquid  
Crystal Television. Please purchase it at your nearest  
shop.  
• Additional optional accessories may be available in the near  
future. When purchasing, please read the newest catalogue  
for compatibility and check the availability.  
29  
 
PC Compatibility Chart  
It is necessary to set the PC correctly to display XGA and WXGA signal.  
PC  
Resolution  
720 x 400  
Horizontal Frequency  
Vertical Frequency  
VESA Standard  
31.5 kHz  
70 Hz  
31.5 kHz  
37.9 kHz  
37.5 kHz  
35.1 kHz  
37.9 kHz  
48.1 kHz  
46.9 kHz  
48.4 kHz  
56.5 kHz  
60.0 kHz  
47.7 kHz  
60 Hz  
72 Hz  
75 Hz  
56 Hz  
60 Hz  
72 Hz  
75 Hz  
60 Hz  
70 Hz  
75 Hz  
60 Hz  
O
O
O
O
O
O
O
O
O
O
O
VGA  
640 x 480  
SVGA  
800 x 600  
PC  
XGA  
1024 x 768  
1360 x 768  
WXGA  
VGA and XGA are registered trademarks of International Business Machines Corp.  
Information on the Software License for This Product  
Software composition  
The software included in this product is comprised of various software components whose individual copyrights  
are held by SHARP or by third parties.  
Software developed by SHARP and open source software  
The copyrights for the software components and various relevant documents included with this product that  
were developed or written by SHARP are owned by SHARP and are protected by the Copyright Act, international  
treaties, and other relevant laws. This product also makes use of freely distributed software and software  
components whose copyrights are held by third parties. These include software components covered by a GNU  
General Public License (hereafter GPL), a GNU Lesser General Public License (hereafter LGPL) or other license  
agreement.  
Obtaining source code  
Some of the open source software licensors require the distributor to provide the source code with the executable  
software components. GPL and LGPL include similar requirements. For information on obtaining the source code  
for the open source software and for obtaining the GPL, LGPL, and other license agreement information, visit the  
following website:  
We are unable to answer any questions about the source code for the open source software. The source code for  
the software components whose copyrights are held by SHARP is not distributed.  
Acknowledgements  
The following open source software components are included in this product:  
• linux kernel/busybox/uClibc/zlib/libpng/libjpeg  
CLEARING THE SECRET NUMBER  
If you forget the secret number, clear the secret number using the following procedure.  
Select an item from the list below to display the secret number input screen. (For operating the on-screen  
display menu, see page 17.)  
1
• “EZ Setup”, “CH Setup”, “Parental CTRL” or “Reset” on the Setup menu.  
• “Color System” or “Software Update” on the Option menu.  
Press and hold both CHr and VOL+ on the TV simultaneously until the message appears on the screen.  
2
.
The secret number is  
• As a precautionary measure, make a note of your secret number above, cut it from this manual, and keep it in a safe place.  
30  
 
Calling for Service  
For location of the nearest Sharp Authorized Service, or to obtain product literature, accessories, supplies, or  
customer assistance, please call 1-800-BE-SHARP.  
LIMITED WARRANTY  
CONSUMER LIMITED WARRANTY  
SHARP ELECTRONICS CORPORATION warrants to the first consumer purchaser that this Sharp brand Liquid Crystal Display product (the  
“Product”), when shipped in its original container, will be free from defective workmanship and materials, and agrees that it will, at its option,  
either repair the defect or replace the defective Product or part thereof with a new or remanufactured equivalent at no charge to the  
purchaser for parts or labor for the period(s) set forth below.  
This warranty does not apply to any appearance items of the Product or if the serial number or model number affixed to the Product has  
been removed, defaced, changed, altered or tampered with. This warranty does not cover installation or signal reception problems. This  
limited warranty will not apply if the Product has been or is being used in a commercial setting or application; this warranty is meant solely  
for the non-commercial, household use of the Product by consumers in their home or residence. If you intend to or already use this Product  
for commercial purposes or in a commercial setting, there are warranties available to cover your use of this Product, the terms of which may  
vary. Please contact 1-888-GO-SHARP for further information.  
In order to enforce your rights under this limited warranty, you should follow the steps set forth below. You must be able to provide proof of  
purchase to the servicer, which proof must include the date of purchase.  
To the extent permitted by applicable state law, the warranties set forth are in lieu of, and exclusive of, all other warranties, express or  
implied. Specifically ALL OTHER WARRANTIES OTHER THAN THOSE SET FORTH ABOVE ARE EXCLUDED, ALL EXPRESS AND  
IMPLIED WARRANTIES INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE, AND FITNESS FOR A PARTICULAR  
PURPOSE ARE SPECIFICALLY EXCLUDED. IF, UNDER APPLICABLE STATE LAW, IMPLIED WARRANTIES MAY NOT VALIDLY BE  
DISCLAIMED OR EXCLUDED, THE DURATION OF SUCH IMPLIED WARRANTIES IS LIMITED TO THE PERIOD(S) FROM THE DATE OF  
PURCHASE SET FORTH BELOW. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS. YOU MAY ALSO HAVE OTHER RIGHTS  
WHICH VARY FROM STATE TO STATE.  
The warranties given herein shall be the sole and exclusive warranties granted by Sharp and shall be the sole and exclusive remedy  
available to the purchaser and only for the time periods set forth herein. No other representations or promises made by anyone are  
permitted. Correction of defects, in the manner and for the period of time described herein, shall constitute complete fulfillment of all  
liabilities and responsibilities of Sharp to the purchaser with respect to the Product, and shall constitute full satisfaction of all claims,  
whether based on contract, negligence, strict liability or otherwise. Sharp does not warrant nor shall Sharp be liable, or in any way  
responsible, for Products which have been subject to abuse (including, but not limited to, improper voltage), accident, misuse, negligence,  
lack of reasonable care, alteration, modification, tampering, misuse, improper operation or maintenance or any damages or defects in the  
Product which were caused by repairs or attempted repairs performed by anyone other than a Sharp authorized servicer. Nor shall Sharp  
be liable or in any way responsible for any incidental or consequential economic or property damage. Some states do not allow limits on  
warranties or on remedies for breach in certain transactions; in such states, the limits herein may not apply.  
THIS LIMITED WARRANTY IS VALID ONLY IN THE FIFTY (50) UNITED STATES, THE DISTRICT OF COLUMBIA AND PUERTO RICO.  
Model Specific Section  
Your Product Model Number & Description:  
Warranty Period for this Product:  
LC-32SB27U LCD Color Television  
(Be sure to have this information available when you need service for your  
Product.)  
One (1) year parts and labor from the date of purchase.  
Additional Exclusions from  
Warranty Coverage (if any):  
Image Retention resulting from  
periods of time is not covered by this Limited Warranty (see Operation  
Manual on how to prevent this).  
a
fixed image being displayed for long  
Where to Obtain Service:  
From a Sharp Authorized Servicer located in the United States. To nd the  
location of the nearest Sharp Authorized Servicer, please call Sharp toll free  
at 1-800-BE-SHARP.  
What to do to Obtain Service:  
Ship prepaid or carry in your Product to a Sharp Authorized Servicer. Be sure  
to have proof of purchase available. If you ship the Product, be sure it is  
insured and packaged securely. Please use two persons to carry the Product,  
transport it in its original packaging, and ensure that the Product is covered  
to avoid scratches and damage. Sharp shall not be responsible for lost,  
stolen or misdirected mail or for damage to the product incurred during  
shipping.  
TO OBTAIN PRODUCT INFORMATION OR PURCHASE ACCESSORIES AND EXTENDED WARRANTIES, CALL 1-800-BE-SHARP  
SHARP ELECTRONICS CORPORATION  
Sharp Plaza, Mahwah, New Jersey 07495-1163  
SHARP CORPORATION  
31  
 

Sony Car Satellite TV System 49X850B User Manual
Sony Flat Panel Television 4 141 448 110 User Manual
Sony Headphones MDR EX71SL User Manual
Sony Microcassette Recorder ICD B25 User Manual
Sony Stereo Receiver SRF HM33 User Manual
Sony Video Game Console 4 156 992 611 User Manual
Sterling Plumbing Indoor Furnishings 26290 User Manual
Summit Printer P4014 User Manual
Sunrise Medical Indoor Furnishings 93000 User Manual
Tanaka Blower TBL 300 User Manual