SIIG TV Mount 04 0541A User Manual

Ultra-Thin LED/LCD TV Mount - 32" to 55"  
Installation Instructions  
Ultra-Thin LED/LCD TV Wall Mount  
Material: 2.0mm Cold Rolled Steel Plate  
TV Size: 32" - 55”  
Max load capacity: 121lbs/55kg  
Wall distance: 0.43/11mm  
Universal Mounting Pattern  
IMPORTANT: If you don't understand the installation instructions, please consult an  
installation specialist  
04-0541A  
1
 
Tools Required  
Phillips head screw driver  
1
2
3
4
5
Stud finder for drywall installation  
Level  
1/2" socket & socket wrench and/or 1/2" open-end wrench  
Drill, 3/16" (5mm) drill bit for wood stud installation and 3/8" (10mm) masonry drill bit for concrete/brick installation  
Step 1: Wall Plate Installation  
a) Wood Stud Installation  
NOTE: When mounting to wood studs, the two wood studs must be a minimum of 16" apart.  
Use a high-quality electronic stud finder (commercially available) to locate dead center of two studs and mark  
their locations with a pencil.  
1
With the help of an assistant, and using a bubble level to ensure the wall plate is level, position the wall plate  
against the wall in the desired mounting location.  
2
Mark the right and the left positions of the small horizontal slots that are in alignment with the studs.  
You should mark two positions total.  
3
4
5
Pre-drill a 3/16" hole to a depth of approximately 3" in the wall stud at each marked location.  
Place the wall plate against the wall and line up the mounting slots with the drilled holes. Check the bubble level  
to verify that the wall plate is level.  
6
For each location, insert bolt (I) into the wall.  
7
8
Tighten the bolt with the 1/2" socket or 1/2" open-end wrench by turning clockwise until tight.  
CAUTION: Do not over-tighten bolts - doing so may cause unnecessary damage to the wall.  
CAUTION: Do not release the wall plate until it is properly mounted and secured to the wall.  
3
 
b) Concrete/Brick Installation  
NOTE: The concrete anchors must be used for concrete installation.  
With the help of an assistant, and using a bubble level to ensure the wall plate is level, position the wall plate  
against the wall in the desired mounting location.  
1
Mark four holes to be used for securing the mount and place the wall plate aside.  
Next, drill holes using a 3/8" masonry drill bit to a depth of approximately 3".  
Insert a concrete anchor into to each hole.  
2
3
4
5
6
7
8
9
If necessary, a hammer can be used to lightly tap each anchor into place so that they are flush with the wall.  
Once all of the anchors are in place, move the wall plate back into position.  
Insert bolt (I) into each concrete anchor in the wall.  
Do not tighten until all bolts are in place.  
Tighten the bolt with the 1/2" socket or 1/2" open-end wrench by turning clockwise until tight.  
CAUTION: Do not over-tighten bolts - doing so may cause unnecessary damage to the wall.  
CAUTION: Do not release the wall plate until it is properly mounted and secured to the wall.  
4
 
Step 2: Display Bracket Installation  
1
2
To ensure optimal installation, this kit includes various screws of different diameters and lengths.  
Place your TV screen down on a soft, flat surface, and locate the threaded mounting points that are located on  
the back of the display.  
Determine which screw (A/B/C/D/E/F) is of the correct length by carefully inserting a straw, or toothpick, and  
mark how deep the mounting point is.  
3
4
5
According to the size of display's hole, choose the corresponding screw (A/B/C/D/E/F) and washer (G/H), then  
thread them in line. Note: when using screw (C/F), no washer is needed. (figures a1, a2, a3)  
If your display has a curved back or a recessed thread mounting point, a spacer (K) must be used. Then choose  
screw (D/E/F) to match and place the spacer between the mounting bracket and display. (figure a5)  
Cut strings to desired length (ensure enough string remains for easy access and use for installation & removal).  
(figure a4)  
6
7
Attach Sponge sticker (L) to the bottom inside of each TV rail. These will help to protect the wall surface. (figure  
a6)  
5
 
Step 3: Final Installation & Adjustment  
Hook the TV rails over the top of the wall plate and lower on to wall plate.  
Pull TV forward from the bottom and connect all TV cables & wires.  
1
2
To secure TV rails, pull strings down to retract locking mechanism & lower bottom of TV to the wall. Let go of  
strings to engage the locking mechanism.  
3
lock hook  
Lift up TV ,  
then pull down the belt  
connect TV wires  
Maintenance  
Check the mounting screws every two months for tightness.  
6
 
Technical Support and Warranty  
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online  
support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks away.  
You can also submit questions online and a technical support analysts will promptly respond.  
SIIG offers a 5-year manufacturer warranty with this product. Please see our web site for more warranty details. If you  
encounter any problems with this product, please follow the procedures below.  
A) If it is within the store's return policy period, please return the product to the store where you purchased from.  
B) If your purchase has passed the store's return policy period, please follow these steps to have the product repaired or  
replaced.  
Step 1: Submit your RMA request.  
defective, an RMA number will be issued.  
Step 2: After obtaining an RMA number, ship the product.  
• Properly pack the product for shipping. All software, cable(s) and any other accessories that came with the original package  
must be included.  
• Clearly write your RMA number on the top of the returned package. SIIG will refuse to accept any shipping package, and will  
not be responsible for a product returned without an RMA number posted on the outside of the shipping carton.  
• You are responsible for the cost of shipping. Ship the product to the following address:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
RMA #: ________________  
• SIIG will ship the repaired or replaced product via Ground in the U.S. and International Economy outside of the U.S. at no cost  
to the customer.  
7
 
About SIIG, Inc.  
Founded in 1985, SIIG, Inc. is a leading computer upgrade manufacturer of I/O connectivity products, including PCI  
& ISA serial and parallel ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b), networking, sound  
cards, and other accessories. SIIG is the premier one-stop source of upgrades.  
SIIG products offer comprehensive user manuals, many user-friendly features, and are backed by an extensive  
manufacturer warranty. High-quality control standards are evident by the overall ease of installation and  
compatibility of our products, as well as one of the lowest defective return rates in the industry. SIIG products can  
be found in computer retail stores, mail order catalogs, through major distributors, system integrators, and VARs in  
the Americas and the UK, and through e-commerce sites.  
PRODUCT NAME  
Ultra-Thin LED/LCD TV Mount - 32" to 55"  
Ultra-Thin LED/LCD TV Mount - 32" to 55" is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Other  
names used in this publication are for identification only and may be trademarks of their respective companies.  
July, 2009  
Copyright © 2009 by SIIG, Inc. All rights reserved.  
8
 

Sennheiser Musical Instrument Amplifier MZN 16 P48 User Manual
Sharp Calculator EL 2139H User Manual
Sony Ericsson Network Router EC400G User Manual
Sony Home Security System Snc Df50n User Manual
Sony Satellite TV System VCA 130 User Manual
Speco Technologies Security Camera CVC5300DPVF CVC5300DPVFW User Manual
Star Manufacturing Fryer 615FD User Manual
StarTechcom Stereo Receiver VGA2HD2 User Manual
Sterling Fan 25001301 User Manual
SUPER MICRO Computer Computer Hardware AOC SASLP MV8 User Manual