SIIG TV Mount 04 0529D User Manual

Universal Tilting TV Mount - 32" to 60"  
Installation Instructions  
Tiltable LCD / TFT TV Wall Mount  
Material: 2.0mm Cold Rolled Steel Plate  
TV Size: 32" - 60"  
Tilt: 0 / +15 degrees  
Maximum load capacity: 165 lbs / 75 kgs  
Wall distance: 3.3" / 84mm  
Bubble level included  
Universal Mounting Pattern  
IMPORTANT: If you don't understand the installation instructions, please  
consult an installation specialist  
04-0529D  
1
 
Note:  
1. Please ensure that the bubble level (L-2) is properly attached to the  
wall plate prior to mounting.  
2. Please check the two rails before installing, if without the  
knob, please detach the screw and install the knob.  
Step 1: Wall plate installation  
A) Wood Stud Installation  
NOTE: For secure wood stud mounting, the wall plate must be mounted to two studs at least  
16" apart.  
1
Use a high-quality electronic stud finder (commercially available)  
to locate two adjacent studs and mark their locations with a  
pencil (1-a).  
2
Attach the bubble level (L-2) to the wall plate and with the help of  
an assistant ensure the wall plate is level, position the wall plate  
against the wall in the desired mounting location (figure 1-b).  
3
Mark the right (upper and lower) and the left (upper and lower)  
positions of the small horizontal slots that are in alignment with  
the studs.  
4
5
You should mark four positions total.  
Pre-drill a /16" hole to a depth of 3" in the wall stud at each  
marked location.  
6
Position the wall plate against the wall and line up the mounting  
slots with the drilled holes. Check the bubble level to verify that  
the wall plate is level.  
7
8
For each location, insert a lag bolt (J) and washer (L-1) into the  
wall (figure 1-c).  
Tighten each bolt with an open ended socket wrench by turning clockwise until tight.  
CAUTION: Do not over-tighten bolts-doing so many cause unnecessary damage to the wall. Avoid excessive  
torque.  
Do not release the wall plate until it is properly mounted and secured to the wall.  
CAUTION:  
3
 
B) Concrete/Brick Installation  
NOTE: The concrete anchors must be used for concrete installation.  
1
Attach the bubble level (L-2) to the wall plate, with the help of an  
assistant place the wall plate into position against the wall, using  
the bubble level to keep it level.  
2
3
Mark four holes to be used for securing the mount and place the  
wall plate aside (figure 1-d).  
Drill holes using an electric drill and 1/2" masonry bit to a depth of  
3".  
4
5
Insert a concrete anchor (K) into to each hole.  
If necessary, a hammer can be used to lightly tap each anchor into place so that they are flush  
with the wall.  
6
7
Once all of the anchors are in place, move the wall plate back into position. Check the bubble  
level to verify that the wall plate is level.  
Insert bolt (J) with washer (L-1) into each concrete anchor in the wall. Do not tighten until all  
screws are in place.  
Step 2 Display Bracket Installation  
1
To ensure optimal installation, this kit includes various screws of  
different diameters and lengths.  
2
Place your TV screen down on a soft, flat surface, and locate the  
threaded mounting points that are located on the back of the  
display.  
3
4
5
Determine which screw (A/B/C/D/E/F/G/H) is of the correct length  
by carefully inserting a straw, or toothpick, and mark how deep  
the mounting point is.  
According to the size of display's hole, choose the corresponding  
screw and hole on the rectangle washer, then thread them in line  
as shown (figure 2-a).  
If your display has a curved back or a recessed thread mounting  
point, place the spacer (M) between the mounting bracket and  
display and then choose screw (F/G/H) to match (figure 2-b).  
Step 3 Final Installation & Adjustment  
1
Hook the TV rails over the top of wall plate (3-a).  
2
The TV rail can be tilted down up to 15 degrees. To make this adjustment, first loosen the knob and pull or  
push the rail until it is in the desired position. Once the desired level of tilt is achieved, re-tighten the mount by  
turning the tension knobs (figure 3-b).  
3
4
On the TV rail equipped with lock, lock it to avoid the theft by rotating the key until the hook touches the bottom  
bar of the wall plate (3-c)  
On the TV rail equipped with screw, rotate the long screw at the bottom of the display rail to tighten it & secure  
mount (figure 3-d).  
Maintenance  
Check the mounting screws every two months for tightness.  
4
 
Blank Page  
5
 
Blank Page  
6
 
Technical Support and Warranty  
QUESTIONS? SIIG’s Online Support has answers! Simply visit our web site at www.siig.com and click Support. Our online  
support database is updated daily with new drivers and solutions. Answers to your questions could be just a few clicks  
away. You can also submit questions online and a technical support analysts will promptly respond.  
SIIG offers a 5-year manufacturer warranty with this product. This warranty covers the original purchaser and guarantees  
the product to be free of any defects in materials or workmanship for five (5) years from the date of purchase of the product.  
SIIG will, at our discretion, repair or replace (with an identical product or product having similar features and functionality) the  
product if defective in materials or workmanship. This warranty gives you specific legal rights, and you may also have other  
rights which vary from state to state. Please see our web site for more warranty details.  
If you encounter any problems with this product, please follow the procedures below.  
A) If it is within the store's return policy period, please return the product to the store where you purchased from.  
B) If your purchase has passed the store's return policy period, please follow these steps to have the product repaired or  
replaced.  
Step 1: Submit your RMA request.  
product is determined to be defective, an RMA number will be issued.  
Step 2: After obtaining an RMA number, ship the product.  
• Properly pack the product for shipping. All software, cable(s) and any other accessories that came with the original  
package must be included.  
• Clearly write your RMA number on the top of the returned package. SIIG will refuse to accept any shipping package, and  
will not be responsible for a product returned without an RMA number posted on the outside of the shipping carton.  
• You are responsible for the cost of shipping the product to SIIG. Ship the product to the following address:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
RMA #: ________________  
• SIIG will ship the repaired or replaced product via Ground in the U.S. and International Economy outside of the U.S. at no  
cost to the customer.  
7
 
About SIIG, Inc.  
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity solutions (including Serial ATA and Ultra  
ATA Controllers, FireWire, USB, and legacy I/O adapters) that bridge the connection between  
Desktop/Notebook systems and external peripherals. SIIG continues to grow by adding A/V and Digital Signage  
connectivity solutions to our extensive portfolio. All centered around the distribution and switching of A/V signals  
over CAT5/6, these products include matrix switches, distribution amplifiers, extenders, converters, splitters,  
cabling, and more.  
SIIG is the premier one-stop source of upgrades and is committed to providing high quality products while  
keeping economical and competitive prices. High-quality control standards are evident by one of the lowest  
defective return rates in the industry. Our products offer comprehensive user manuals, user-friendly features,  
and most products are backed by a lifetime warranty.  
SIIG products can be found in many computer retail stores, mail order catalogs, and e-commerce sites in the  
Americas, as well as through major distributors, system integrators, and VARs.  
PRODUCT NAME  
Universal Tilting TV Mount - 32" to 60"  
Universal Tilting TV Mount - 32" to 60" is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Other  
names used in this publication are for identification only and may be trademarks of their respective owners.  
November, 2010  
Copyright © 2010 by SIIG, Inc. All rights reserved.  
8
 

Sharp All in One Printer MX M260 User Manual
Sharp Flat Panel Television LC 52SB55U User Manual
Soehnle Scale 2761 User Manual
Sony Cell Phone P910a User Manual
Sony Security Camera SSC CD43VP User Manual
Sony Speaker System CMT CP300 User Manual
Sony Speaker System SA VE545H User Manual
Studio RTA Portable Speaker Component Speaker User Manual
Sunrise Medical Mobility Aid Ti Titanium User Manual
Tandberg Data Cassette Player LTO 1 HH User Manual