SIIG Network Card 04 0448A User Manual

FireWire 800 2-Port  
ExpressCard/34  
Quick Installation Guide  
Introducing the FireWire 800 ExpressCard  
The FireWire 800 2-Port ExpressCard/34 adds FireWire 800  
(1394b)interfacetoyourExpressCardequippednotebook  
computer.  
FeaturesandBenefits  
Provides 2 FireWire 800 (9-pin) ports for multiple  
device connections  
Supports data transfer rates up to 800Mb/s  
Supports hot-swap, hot-plug and Plug-n-Play  
connection of peripheral devices  
Works with FireWire devices including DV  
camcorders, CD-RW/DVD-ROM drives, portable  
hard disks, digital cameras and other audio/video  
devices  
SystemRequirements  
ExpressCard-enablednotebookPCwithanavailable  
ExpressCard slot  
Windows 2000/XP/Server 2003/Vista  
PackageContents  
FireWire 800 2-Port ExpressCard/34  
Driver CD  
Quick Installation Guide  
04-0448A  
 
1
Driver Installation  
This section provides information on how to install the  
FireWire 800 drivers.  
Windows2000  
Windows 2000 automatically installs it's built-in 1394a  
driver for the FireWire 800 2-Port ExpressCard/34. To get  
the full speed out of this controller, install the FireWire  
800 driver using the directions below.  
1. Insert the driver CD. Click Start, Run. Type  
D:\setup.exe, click OK. (Change D: to match the  
drive letter of your CD-ROM)  
2. At the Welcome screen, click Next.  
3. At the License Agreement screen, click Yes.  
4. Typeinyourcustomerinformation,then clickNext.  
5. At the Destination Location screen, click Next.  
6.  
Select Complete, then click Next.  
7. At the Program Folder screen, click Next.  
8.  
AttheDigitalSignaturescreen,clickYesthreetimes,  
then click Finish.  
9. SelecttherestartWindowsoption, thenclickFinish.  
WindowsXP  
Windows XP automatically installs it's built-in 1394a  
driver for the FireWire 800 2-Port ExpressCard/34. To get  
the full speed out of this controller, install the FireWire  
800 driver using the directions below.  
1. Insert the driver CD. Click Start, Run. Type  
D:\setup.exe, click OK. (Change D: to match the  
drive letter of your CD-ROM)  
3
 
2. At the Welcome screen, click Next.  
3. At the License Agreement screen, click Yes.  
4. Typeinyourcustomerinformation,then clickNext.  
5. At the Destination Location screen, click Next.  
6.  
Select Complete, then click Next.  
7. At the Program Folder screen, click Next.  
8. At the Hardware Installation screen, click Continue  
Anyway three times, then click Finish.  
9. SelecttherestartWindowsoption, thenclickFinish.  
WindowsServer2003  
Windows Server 2003 automatically installs it's  
built-in FireWire 400 driver for the FireWire 800 2-Port  
ExpressCard/34. Togetthefullspeedoutofthiscontroller,  
installtheFireWire800driverusingthedirectionsbelow.  
1. Insert the driver CD. Click Start, Run. Type  
D:\setup.exe, click OK. (Change D: to match the  
drive letter of your CD-ROM)  
2. At the Welcome screen, click Next.  
3. At the License Agreement screen, click Yes.  
4. Typeinyourcustomerinformation,then clickNext.  
5. At the Destination Location screen, click Next.  
6.  
Select Complete, then click Next.  
7. At the Program Folder screen, click Next.  
8. At the Security Alert box, click Yes. (Click Yes two  
times for 2003 Standard Edition)  
9. At the Hardware Installation screen, click Continue  
Anyway two times (click Continue Anyway three  
times for 2003 Standard Edition), then click Finish.  
10. SelecttherestartWindowsoption, thenclickFinish.  
4
 
WindowsVista  
WindowsVistaautomaticallyinstallsit'sbuilt-inFireWire  
400 driver for the FireWire 800 2-Port ExpressCard/34. To  
getthefullspeedoutofthiscontroller,installtheFireWire  
800 driver using the directions below.  
1. Insert the driver CD. Click Start, Run. Type  
D:\setup.exe, click OK. (Change D: to match the  
drive letter of your CD-ROM)  
2. Click Allow.  
3. At the Welcome screen, click Next.  
4. At the License Agreement screen, click Yes.  
5. Type in your customer information, then click Next.  
6. At the Destination Location screen, click Next.  
7.  
Select Complete, then click Next.  
8. At the Program Folder screen, click Next.  
9. At the Windows Security box, click Install this  
driversoftwareanywayfourtimes,thenclickFinish.  
10. SelecttherestartWindowsoption, thenclickFinish.  
VerifyProperInstallation  
1. Right click My Computer, click Manage, then click  
Device Manager.  
2. Double click 1394 Bus host controllers. IEEE 1394b  
(FireWire 800) adapter should be displayed.  
5
 
Removing the ExpressCard  
Stop the ExpressCard before removing it from the  
ExpressCard slot.  
1
The utility is located by the system clock.  
For Windows 2000: Click the Unplug or Eject  
Hardware icon. Click Remove PCI standard  
PCI-to-PCI bridge.  
For Windows XP/Server 2003/Vista: Click the Safely  
Remove Hardware icon. Click Safely remove PCI  
standard PCI-to-PCI bridge.  
2. Wait for the confirmation box, then remove the  
ExpressCard from the ExpressCard slot.  
Connecting Devices  
General driver installation steps are provided below.  
Pleasereviewyourdevice'susermanualformoredetails.  
Windows2000  
1. At the Found New Hardware Wizard, click Next.  
2. SelectSearchforasuitabledriver...,thenclickNext.  
3. Uncheck all check boxes, then click Next.  
4. Click Next, then click Finish to complete the  
installation.  
WindowsXP  
1. At the Found New Hardware Wizard,  
For XP w/SP2 or later  
Select No, not this time, then click Next.  
For XP w/SP1 or earlier  
Go directly to step #2.  
6
 
2. SelectInstalltheSoftwareAutomatically,clickNext.  
3. Click Continue Anyway. (Skip if not prompted)  
4. Click Finish to complete the installation.  
Server2003  
1. At the Found New Hardware Wizard,  
For 2003 w/SP1 or later  
Select No, not this time, then click Next.  
For 2003 no service pack installed  
Go directly to step #2.  
2. SelectInstalltheSoftwareAutomatically,clickNext.  
3. At the Security Alert box click Yes, or the Hardware  
Installation box click Continue Anyway, then click  
Finish to complete the installation.  
WindowsVista  
Windows Vista will automatically detect and install  
most FireWire devices when connected. However, for  
devices that do not install automatically, follow the steps  
below to complete the installation.  
1. Click Locate and install driver software.  
2. Click Continue to complete the installation.  
7
 
ubSwitch Utility  
In order to use a DV camcorder with this controller,  
Microsoft's FireWire 400 driver must be installed in the  
system. We have supplied an easy to use utility that  
allows switching between Microsoft's driver and the  
FireWire 800 driver. Before using this utility, unplug all  
devices from the FireWire 800 2-Port ExpressCard/34.  
1. Click Start, Programs, Unibrain ubcore, Tools then  
ubSwitch.  
2. Right click the ubSwitch icon located in the system  
tray by the clock.  
3. Clickthe1394Adapterthatyouwanttoswitch,then  
click on Microsoft 1394 Drivers.  
Note: If your system has multiple 1394 adapters  
installed, make sure that you click on the 1394  
adapter that the camcorder will be plugged into.  
4. Windows will display an information box when the  
driver is ready for use. It may take a few seconds for  
this box to appear.  
Note: To switch back to the FireWire 800 driver,  
follow the same procedures, but in step 3 instead of  
clickingonMicrosoft1394Drivers, clickonUnibrain  
1394 Drivers.  
8
 
Blank Page  
9
 
Blank Page  
10  
 
Technical Support and Warranty  
QUESTIONS?  
SIIG’s Online Support has answers!  
Simply visit our website at www.siig.com and click on Support.  
Our online support database is updated daily with new drivers  
and solutions. Answers to your questions could be just a few clicks  
away. Youcanalsosubmitquestionsonlineandoneofourtechnical  
support analysts will promptly respond.  
Thisproductcomeswithalifetimemanufacturerwarranty. Pleasesee  
SIIGwebsiteformorewarrantydetails. Ifyoushouldhappentohave  
any problems with this product, follow the procedures below.  
A) If it is within the store's return policy period, please return the  
product to the store where you purchased from.  
B) Ifyourpurchasehaspassedthestore'sreturnpolicyperiod,please  
follow these steps to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Go to www.siig.com, click Support, then RMA to submit a  
request to SIIG RMA. If the product is determined to be  
defective,anRMAnumberwillbeissued. SIIGRMAdepartment  
can also be reached at (510)413-5333.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All software, cable(s)  
and any other accessories that came with the original package  
must be included.  
Clearly write your RMA number on the top of the returned  
package. SIIG will refuse to accept any shipping package, and  
will not be responsible for a product returned without an  
RMA number posted on the outside of the shipping carton.  
You are responsible for the cost of shipping. Ship the product  
to the following address:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538  
RMA#:  
SIIG will ship the repaired or replaced product via Ground  
in the U.S. and International Economy outside of the U.S. at  
no cost to the customer.  
11  
 
About SIIG, Inc.  
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer  
ofI/Oconnectivityproducts,includingPCI&ISAserialandparallel  
ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b),  
Networking,SoundCards,andotheraccessories. SIIGisthepremier  
one-stop source of upgrades.  
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendly  
features, and are backed by an extensive manufacturer warranty.  
High-quality control standards are evident by the overall ease of  
installation and compatibility of our products, as well as one of the  
lowest defective return rates in the industry. SIIG products can be  
foundincomputerretailstores,mailordercatalogs,ande-commerce  
sitesintheAmericasandtheUK,aswellasthroughmajordistributors,  
system integrators, and VARs.  
PRODUCT NAME  
FireWire 800 2-Port ExpressCard/34  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS  
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not cause  
harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Ave.  
Fremont, CA 94538-3152  
FireWire 800 2-Port ExpressCard/34 is a trademark of SIIG, Inc.  
SIIG and the SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are  
registered trademarks of Microsoft Corporation. Other names used in this publication are for  
identificationonlyandmaybetrademarksoftheirrespectivecompanies.  
March, 2007  
Copyright ©2007 by SIIG, Inc. All rights reserved.  
 

Sharp Air Conditioner AFP80CX User Manual
Sharp Computer Monitor LL T15A4 User Manual
Sharp Printer AR 350 User Manual
Sharp Projector XG C435X User Manual
Sonic Alert Door DB200 User Manual
Sony Stereo System CHC CL3 User Manual
Southwestern Bell Cordless Telephone GH3012NB User Manual
SOYO Computer Hardware SY 7VMA B User Manual
Subaru Robin Power Products Portable Generator RG2800I User Manual
Sunbeam Coffeemaker EM5800 User Manual