SIIG Computer Hardware 1S1P PCI User Manual

Cyber 1S1P PCI  
Quick Installation Guide  
Introducing the Cyber 1S1P PCI  
The Cyber 1S1P PCI high-speed serial I/ O card provides  
one 9-pin serial port and one parallel port.  
FeaturesandBenefits  
Conforms to PCI v2.2 Plug and Play  
Full support for Windows-based software  
Red u ces CPU load and im p roves system  
performance dramatically  
IRQ sharing feature reduces IRQ conflicts  
High-speed serial port (9-pin) works with 56K V.90  
external modems, ISDN terminal adapters, PDAs,  
digital cameras, label printers and other serial port  
devices  
Built-in FIFO buffers dramatically increase data  
transmit/ receive speed,especially under Windows'  
multitasking environment  
Each serial port can be configured for either 5v or  
12v output, for serial devices that require power  
IEEE 1284 compliant SPP/ EPP/ ECP parallel port  
SystemRequirements  
Pentium or equivalent computer with an available  
PCI slot  
Windows 95/ 98/ 98SE/ ME/ NT 4.0/ 2000/ XP/  
Server 2003  
04-0344A  
 
1
Hardware Installation  
General instructions for installing the card are provided  
below , since the d esign of com p u ter cases and  
motherboards vary. Refer to your computers reference  
manual for further information, if needed.  
Static Electricity Discharge may permanently damage  
your system. Discharge any static electricity build up in  
your body by touching your computers case for a few  
seconds. Avoid any contact with internal parts and  
handle cards only by their external edges.  
1. Turn OFF the power to your computer and any  
other connected peripheral devices.  
2. Unplug the power cord from the back of the  
computer.  
3. Remove your computers cover.  
4. Remove the slot bracket from an available PCI slot.  
5. Change JP1 jumper settings to the desired voltage  
only if your serial device needs additional power  
from the serial port. However, most serial devices  
do not require additional power. For more  
information, see Figure 1 on page 2. Skip this step  
if power is not required.  
6. To install the card, carefully align the card's bus  
connector w ith the selected PCI slot on the  
motherboard. Push the board down firmly, but  
gently, until it is well seated.  
7. Replace the slot bracket's holding screw to secure  
the card.  
8. Replacethecomputer cover and reconnect thepower  
cord.  
3
 
Software Installation  
This section provides information on how to install the  
Cyber 1S1P PCI drivers.  
Windows95DriverInstallation  
1. At the Update Device Driver Wizard window, click  
Next.  
2. Insert the driver CD, and click Other Locations.  
Type in D:\ 9x, click OK, then Finish. (Change D: to  
match your CD-ROM drive letter)  
3. From the Insert Disk window, click OK. When the  
Cop yin g Files d ialog box ap p ears, typ e in  
D:\ 9x, then click OK.  
4.  
Repeat steps 1-3.  
5. Restart Windows to complete the installation.  
Windows98/98SEDriverInstallation  
1. At the Add New Hardware Wizard window, click  
Next.  
2. Select Search for the best driver for your device  
(Recommended), then click Next.  
3. Select Specify a location, uncheck the other boxes,  
insert the driver CD, type in D:\ 9x, then click Next.  
(Change D: to match your CD-ROM drive letter)  
4.  
5.  
Click Next, then Finish.  
Repeat steps 1-4.  
6. Restart Windows to complete the installation.  
4
 
WindowsMEDriverInstallation  
1. At the Add New Hardware Wizard,chooseSpecify  
the location of the driver (Advanced), then click  
Next.  
2. Check Specify a location, uncheck the other box,  
insert the driver CD, type in D:\ Me, then click  
Next. (Change D: to match your CD-ROM drive  
letter)  
3. Click Next and Finish.  
4.  
Repeat steps 1-3.  
5. Restart Windows to complete the installation.  
To Verify Successful Installation In Windows 95/98/  
98SE/ME:  
1. From the main desktop, right click My Computer,  
click Properties, then click Device Manager.  
2. Double click Ports (COM & LPT), CyberSerial PCI  
16Cxxx..., Printer Port..., and CyberParallel PCI  
should be displayed.  
3. Double click M u lti-fu n ction ad ap ters, SIIG  
CyberPro 1S1P PCI board should be displayed.  
Windows NT 4.0 Driver Installation  
1. From the desktop click Start, then Run.  
2. Insert  
the  
d river  
CD,  
typ e  
in  
D:\ NT4\ Install_Serial.exe,then click OK. (Change  
D: to match your CD-ROM drive letter)  
3. Click Next when the Welcome window appears.  
4. Choose Install, then click Next.  
5. Click Yes, then click Exit.  
6. From the desktop click Start, then Run.  
5
 
7. Typein D:\ NT4\ Install_Parallel.exe,then click OK.  
(Change D: to match your CD-ROM drive letter)  
8.  
Repeat steps 3-5.  
9. Click Yes to restart Windows to complete the  
installation.  
To Verify Successful Installation In Windows NT 4.0:  
1. Go to Start / Settings / Control Panel, double click  
Ports device icon.  
2.  
A new COM port willbe assigned when successfully  
installed.  
3. Click Start, Programs, Administrative Tools,  
Windows NT Diagnostics. Click Resources tab,  
SIIGpar and SIIGser should be displayed.  
Windows2000DriverInstallation  
1. At the Found New Hardware Wizard, click Next.  
2. Select Search for a suitable driver for my device  
(recommended), and click Next.  
3. Select Specify a location, uncheck the other boxes,  
and click Next.  
4. Insert the driver CD, type in D:\ 2000, then click OK.  
(Change D: to match your CD-ROM drive letter)  
5. Click Next and Finish.  
6. Repeat steps 1-5 two more times.  
7. Restart Windows to complete the installation.  
WindowsXPDriverInstallation  
1. At the Found New Hardware Wizard,chooseInstall  
from a list or specific location (Advanced), then  
click Next.  
6
 
2. Insert the driver CD, check Include this location in  
the search, uncheck the other check box, type in  
D:\ XP, and click Next. (Change D: to match your  
CD-ROM drive letter)  
3. At the Hardware Installation window, click  
Continue Anyway, then Finish. Our driver has been  
testedfor stabilityandcompatibility.  
4. Repeat steps 1-3 two more times.  
5. Restart Windows to complete the installation.  
WindowsServer2003DriverInstallation  
1. At the Found New Hardware Wizard,chooseInstall  
from a list or specific location (Advanced), then  
click Next.  
2. Insert the driver CD, check Include this location in  
the search, uncheck the other check box, type in  
D:\ 2003, and click Next. (Change D: to match your  
CD-ROM drive letter)  
3. At the Hardware Installation window, click  
Continue Anyway, then Finish. Our driver has been  
testedfor stabilityandcompatibility.  
4. Repeat steps 1-3 two more times.  
5. Restart Windows to complete the installation.  
To Verify Successful Installation In Windows 2000/XP/  
Server 2003:  
1. Right click My Computer, click Manage, then select  
Device Manager.  
2. Double click Ports (COM & LPT), CyberSerial PCI  
16Cxxx... and Cyb erParallel PCI... should be  
displayed.  
3. Dou ble click M u ltifu n ction ad ap ters, SIIG  
CyberPro 1S1P PCI board should be displayed.  
7
 
Changing COM Port Address  
Some serial devices need a specific COM port in order to  
work. If your serial device works properly, do not  
change this setting.  
Windows95/98/98SE/ME  
1. From the Device Manager window double click  
Ports (COM & LPT), then double click CyberSerial  
PCI... serial port.  
2. Click Settings tab, at the Port Name box click the  
down arrow and select a COM address that is not  
currently in use.  
3.  
Click OK, click OK again to close Device Manager  
to save the changes.  
Windows2000/XP/Server2003  
1. From the Device Manager window double click  
Ports (COM & LPT), then double click CyberSerial  
PCI... serial port.  
2. Click Settings tab and click Advanced....  
3. At the COM Port number box, click the down arrow  
and select a COM port that is not in use. Click OK.  
4. Click OK, then close Device Manager to save the  
changes.  
8
 
Changing Parallel Port Address (LPT)  
Some parallel devices need a specific parallel port in  
order to work. If your parallel device works properly, do  
not change this setting.  
Windows95/98/98SE/ME  
1. From the Device Manager window double click  
Ports (COM & LPT),then doubleclick CyberParallel  
PCI.  
2. Click Settings tab, check Enable use of I/O location  
278h.  
3. Click OK, click OK again to close Device Manager,  
and click Yes to restart Windows to save the changes.  
Windows2000/XP/Server2003  
1. From the Device Manager window double click  
Ports (COM & LPT),then doubleclick CyberParallel  
PCI....  
2. Click Port Settings tab.  
3. At the LPT Port Number box, click the down arrow  
and select an LPT port that is not in use.  
4. Click OK, then close Device Manager to save the  
changes.  
9
 
Blank Page  
10  
 
Technical Support  
QUESTIONS? SIIG’s Online Support has the answers!  
Simply visit our Web site at www.siig.com and click on  
Support. Our online support database is updated daily  
with new drivers and solutions. The answers to your  
problems could be just a few clicks away.  
If you can't find answers or solutions to your questions, you  
have an option to submit the problems online to one of our  
technical support analysts and we will promptly respond  
to you with answers or solutions.  
The 5-year manufacturer warranty supplied with this  
product is offered by SIIG, Inc. If you should happen to  
encounter any problems with this product, please follow  
the procedures below.  
1.  
If it is within the store's return policy period, please  
return the product to the store where you purchased  
from.  
2.  
If your purchase has passed the store's return policy  
period, please contact SIIG. See SIIG's Limited 5-year  
Warranty card for more information.  
Online Store  
SIIG offers all of our products online at our company  
store. Visit us at http://onlinestore.siig.com to find  
our complete line of products, including hard to find  
items and accessories (power adapters, cables,  
upgrade kits, etc.).  
11  
 
About SIIG, Inc.  
Founded in 1985, SIIG, Inc. is a leading computer upgrade  
manufacturer of I/ O connectivity products, including PCI & ISA  
serial and parallel ports, USB, Serial ATA & UltraATA controllers,  
FireWire(1394a/ b),Networking,Sound Cards,and other accessories.  
SIIG is the premier one-stop source of upgrades.  
SIIGproductsoffer comprehensiveuser manuals,many user-friendly  
features, and all products are backed by a 5-year manufacturer  
warranty. High-quality controlstandards are evident by the overall  
ease ofinstallation and compatibility ofour products,as wellas one  
ofthelowest defectivereturn ratesin theindustry. SIIG productscan  
be found in most computer retail stores, mail order catalogs, and  
e-commerce sites in the Americas and the UK, as well as through  
major distributors, system integrators, and VARs.  
PRODUCT NAME  
Cyber 1S1P PCI  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B  
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not  
cause harmful interference, and (2) this device must accept any  
interference received, including interference that may cause undes-  
ired operation.  
THE PARTY RESPONSIBLE FOR  
PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Ave.  
Fremont, CA 94538-3152  
Cyber 1S1P PCI is a trademark of SIIG, Inc.  
SIIG and SIIG logo are registered trademarks of SIIG, Inc. Microsoft and Windows are  
registered trademarks of Microsoft Corporation. Pentium is a registered trademark of Intel  
Corporation. Other names used in publication are for identification only and may be trademarks  
oftheir respectivecompanies.  
July, 2004  
Copyright ©2004 by SIIG, Inc. All rights reserved.  
 

Sherwood Blu ray Player BDP 904 User Manual
Shindaiwa Trimmer DH2510 EVC User Manual
Shure Hair Dryer M97 xE User Manual
Silvercrest Mixer SHMS 300 A1 User Manual
Snapper Snow Blower 1600201 User Manual
Sony Flat Panel Television 40EX621 User Manual
Subaru Robin Power Products Portable Generator R1210 User Manual
Sunbeam Refrigerator SBCR039W User Manual
Swann Security Camera Single Channel Digital Security Recorder User Manual
Tamron Satellite Radio IC R10 User Manual