SIIG Computer Hardware 04 0743A User Manual

DP SATA 6Gb/s 2-Port PCIe  
Quick Installation Guide  
Introduction  
The DP SATA 6Gb/s 2-Port PCIe adds 2 SATA  
6Gb/ s to PCIe-equipped computers.  
Features and Benefits  
Adds 2internal SATA 6Gb/ s channels to  
your PCIe system  
Compliant with SerialATA specification,  
Revision 3.0  
Supports ATA/ ATAPI-7 specification  
Supports port multiplier  
Installs in standard height or low profile  
chassis with included brackets  
System Requirements  
Desktop PC with an available PCIe slot  
Windows® 7 (32-/ 64-bit) / Vista (32-/ 64-  
bit) / XP (32-/ 64-bit) / Server 2003 & 2008  
(32/ 64-bit) / Server 2008 R2  
1
04-0743A  
 
HardwareInstallation  
For Low profile systems, install the spare low  
profile bracket now.  
General instructions for installing the card are  
provided below. Since the design of computer  
cases and motherboards vary, refer to your  
com p u ters reference m anu al for fu rther  
information, if needed.  
Static Electricity Discharge may permanently  
d am age your system . Discharge any static  
electricity build up in your body by touching your  
computer case for a few seconds. Avoid any  
contact with internal parts and handle cards  
only by their external edges.  
1.  
Turn OFF the power to your computer and  
any other connected peripheral devices.  
Unplug the power cord from the back of the  
computer.  
2.  
3.  
4.  
Remove your computer cover.  
Remove the slot bracket cover from an  
available PCI Express slot.  
3
 
5.  
6.  
To install the card, carefully align the card's  
bus connector with the selected PCI Express  
slot on the motherboard. Push the board  
down firmly, but gently, until it is well  
seated.  
Replace the slot bracket holding screw to  
secure the card.  
Device Connection  
The DP SATA 6Gb/s 2-Port PCIe is a dual channel  
Serial ATA III controller that supports up to two  
Serial ATA hard disk drives. If you plan to use  
the second channel, you will need to purchase  
another SATA data cable.  
1.  
2.  
Install your hard disk drive(s) in the chassis.  
Connect the Serial ATA hard disk drive to  
the system power supply.  
Note: For hard drives with both SATA  
p ow er connector and legacy 5-p in  
connector, use either the SATA power  
connector or the legacy 5-pin pow er  
connector. Using both power connectors  
may damage the hard drive.  
Do4wnload from Www.Somanuals.com. All Manuals Search And Download.  
3.  
Connect one end of the Serial ATA cable to  
the hard disk drive.  
Serial ATA  
Power  
Figure 2. SATA hard disk drive connections  
4.  
5.  
Attach the other end of the Serial ATA data  
cable to the Serial ATA connector on the DP  
SATA 6Gb/s 2-Port PCIe.  
Follow the same instructions to connect the  
second hard d rive, if need ed . Device  
connection is now complete.  
SoftwareInstallation  
This section provides information on how to  
install the DP SATA 6Gb/s 2-Port PCIe adapter  
drivers in the next page.  
5
 
Windows 7 (32-/64-bit) / Server 2008 R2  
For New Installation  
1.  
Install the board and follow Microsoft  
procedures to install Windows accordingly.  
After the installation, insert driver CD, click  
Start menu, in the Search programs and  
files box, type D:\ setup.exe, press Enter.  
(Change D: to match your CD-ROM drive  
letter)  
2.  
3.  
At the User Account Control window, click  
Yes. Skip this step if not prompted.  
Click Next.  
Select I accept the terms of the license  
agreement, then click Next.  
4.  
5.  
6.  
7.  
Click Finish.  
Click Yes to complete the installation.  
For Existing Installation  
1. Install the board and boot up Windows.  
Do6wnload from Www.Somanuals.com. All Manuals Search And Download.  
2.  
3.  
Insert driver CD, click Start menu, click  
Start menu, in the Search programs and  
files box, type D:\ setup.exe, press Enter.  
(Change D: to match your CD-ROM drive  
letter)  
At the User Account Control window, click  
Yes. Skip this step if not prompted.  
Click Next.  
4.  
5.  
Select I accept the terms of the license  
agreement, then click Next.  
6.  
7.  
Click Finish.  
Click Yes to complete the installation.  
Windows Vista (32-/64-bit)  
For A New Installation  
1.  
Install the board and follow Microsoft  
procedures to install Windows accordingly.  
After the installation, insert driver CD, click  
Start menu, in the Start Search box, type  
D:\ setup.exe, press Enter. (Change D: to  
match your CD-ROM drive letter)  
At the User Account Control window, click  
Allow. Skip this step if not prompted.  
7
2.  
3.  
 
4.  
5.  
Click Next.  
Select I accept the terms of the license  
agreement, then click Next.  
Click Finish.  
6.  
7.  
Click Yes to complete the installation.  
For Existing Installation  
1.  
2.  
Install the board and boot up Windows.  
At the Found New Hardware window,  
click Cancel.  
3.  
Insert driver CD, click Start menu, in the  
Start Search box, type D:\ setup.exe, press  
Enter. (Change D: to match your CD-ROM  
drive letter)  
4.  
At the User Account Control window, click  
Allow. Skip this step if not prompted.  
Click Next.  
Select I accept the terms of the license  
agreement, then click Next.  
5.  
6.  
7.  
8.  
Click Finish.  
Click Yes to complete the installation.  
Do8wnload from Www.Somanuals.com. All Manuals Search And Download.  
Windows Server 2008 (32-/64-bit)  
For New Installation  
1.  
Install the board and follow Microsoft  
procedures to install Windows accordingly.  
After the installation, insert driver CD, click  
Start menu, in the Start Search box, type  
D:\ setup.exe, press Enter. (Change D: to  
match your CD-ROM drive letter)  
Click Next.  
2.  
3.  
4.  
Select I accept the terms of the license  
agreement, then click Next.  
5.  
6.  
Click Finish.  
Click Yes to complete the installation.  
For Existing Installation  
1.  
2.  
Install the board and boot up Windows.  
At the Found New Hardware window,  
click Cancel.  
3.  
Insert driver CD, click Start menu, in the  
Start Search box, type D:\ setup.exe, press  
Enter. (Change D: to match your CD-ROM  
drive letter)  
9
 
4.  
5.  
Click Next.  
Select I accept the terms of the license  
agreement, then click Next.  
Click Finish.  
6.  
7.  
Click Yes to complete the installation.  
Server 2003 (64-bit)  
For A New Installation  
A new installation requires a floppy disk for the  
driver installation. To make this floppy disk,  
copy the contents of the 64bit folder, found on  
the driver CD, onto a blank floppy disk then  
follow the directions below.  
1.  
2.  
3.  
Install the board and follow Microsoft  
procedures to install Windows accordingly.  
At the Windows Setup screen, press F6 to  
install the RAID driver.  
When prompted, press S to specify the  
location of the driver.  
4.  
5.  
Insert the floppy disk, then press Enter.  
Select Asmedia 106x SATA Controller  
64bit, then press Enter.  
Do10wnload from Www.Somanuals.com. All Manuals Search And Download.  
Note: Do not remove the floppy diskette  
from the floppy drive. You need to install  
the d river once again d u ring the  
installation.  
6.  
Press En ter again to finish the d river  
installation, then follow the on-screen  
instructions to complete your Windows  
installation.  
For Existing Installation  
1.  
2.  
Install the board and boot up Windows.  
At the Found New Hardware window,  
click Cancel.  
3.  
Insert driver CD, click Start menu, Run.  
Type D:\ setup.exe, click OK. (Change D:  
to match your CD-ROM drive letter)  
Click Next.  
Select I accept the terms of the license  
agreement, then click Next.  
4.  
5.  
6.  
7.  
Click Finish.  
Click Yes to complete the installation.  
11  
 
Server 2003 (32-bit)  
For A New Installation  
A new installation requires a floppy disk for the  
driver installation. To make this floppy disk,  
copy the contents of the 32bit folder, found on  
the driver CD, onto a blank floppy disk then  
follow the directions below.  
1.  
2.  
3.  
Install the board and follow Microsoft  
procedures to install Windows accordingly.  
At the Windows Setup screen, press F6 to  
install the RAID driver.  
When prompted, press S to specify the  
location of the driver.  
4.  
5.  
Insert the floppy disk, then press Enter.  
Select Asmedia 106x SATA Controller  
32bit, then press Enter.  
Note: Do not remove the floppy diskette  
from the floppy drive. You need to install  
the d river once again d u ring the  
installation.  
Do12wnload from Www.Somanuals.com. All Manuals Search And Download.  
6.  
Press En ter again to finish the d river  
installation, then follow the on-screen  
instructions to complete your Windows  
installation.  
For Existing Installation  
1.  
2.  
Install the board and boot up Windows.  
At the Found New Hardware window,  
click Cancel.  
3.  
Insert driver CD, click Start menu, Run.  
Type D:\ setup.exe, click OK. (Change D:  
to match your CD-ROM drive letter)  
Click Next.  
Select I accept the terms of the license  
agreement, then click Next.  
4.  
5.  
6.  
7.  
Click Finish.  
Click Yes to complete the installation.  
13  
 
Windows XP (64-bit)  
For A New Installation  
A new installation requires a floppy disk for the  
driver installation. To make this floppy disk,  
copy the contents of the 64bit folder, found on  
the driver CD, onto a blank floppy disk then  
follow the directions below.  
1.  
2.  
3.  
Install the board and follow Microsoft  
procedures to install Windows accordingly.  
At the Windows Setup screen, press F6 to  
install the RAID driver.  
When prompted, press S to specify the  
location of the driver.  
4.  
5.  
Insert the floppy disk, then press Enter  
Select Asmedia 106x SATA Controller  
64bit, then press Enter.  
Note: Do not remove the floppy diskette  
from the floppy drive. You need to install  
the d river once again d u ring the  
installation.  
Do14wnload from Www.Somanuals.com. All Manuals Search And Download.  
6.  
Press En ter again to finish the d river  
installation, then follow the on-screen  
instructions to complete your Windows  
installation.  
For Existing Installation  
1.  
2.  
Install the board and boot up Windows.  
At the Found New Hardware window,  
click Cancel.  
3.  
Insert driver CD, click Start menu, Run.  
Type D:\ setup.exe, click OK. (Change D:  
to match your CD-ROM drive letter)  
Click Next.  
Select I accept the terms of the license  
agreement, then click Next.  
4.  
5.  
6.  
7.  
Click Finish.  
Click Yes to complete the installation.  
15  
 
Windows XP (32-bit)  
For A New Installation  
A new installation requires a floppy disk for the  
driver installation. To make this floppy disk,  
copy the contents of the 32bit folder, found on  
the driver CD, onto a blank floppy disk then  
follow the directions below.  
1.  
2.  
3.  
Install the board and follow Microsoft  
procedures to install Windows accordingly.  
At the Windows Setup screen, press F6 to  
install the RAID driver.  
When prompted, press S to specify the  
location of the driver.  
4.  
5.  
Insert the floppy disk, then press Enter  
Select Asmedia 106x SATA Controller  
32bit, then press Enter.  
Note: Do not remove the floppy diskette  
from the floppy drive. You need to install  
the d river once again d u ring the  
installation.  
Do16wnload from Www.Somanuals.com. All Manuals Search And Download.  
6.  
Press En ter again to finish the d river  
installation, then follow the on-screen  
instructions to complete your Windows  
installation.  
For An Existing Installation  
1.  
2.  
Install the board and boot up Windows.  
At the Found New Hardware window,  
click Cancel.  
3.  
Insert driver CD, click Start menu, Run.  
Type D:\ setup.exe, click OK. (Change D:  
to match your CD-ROM drive letter)  
Click Next.  
Select I accept the terms of the license  
agreement, then click Next.  
4.  
5.  
6.  
7.  
Click Finish.  
Click Yes to complete the installation.  
17  
 
To Verify Windows Installation  
1.  
Use Device Manager to verify installation.  
For Windows 7: Right click Computer, click  
Manage, click Device Manager.  
For Windows Vista: Right click Computer,  
click Manage, click Continue. Click Device  
Manager.  
For Windows XP / Server 2003: Right click  
My Computer, click Manage, click Device  
Manager.  
For Windows Server 2008: Right click  
Computer, click Manage. Double click  
Diagnostics, click Device Manager.  
For Windows 7 / Vista / Server 2008 / Server  
2008 R2: Double click IDE ATA/ATAPI  
con trollers. Asm ed ia 106x SATA  
Controller should be displayed.  
For Windows XP / Server 2003: Double click  
SCSI and RAID controllers. Asmedia 106x  
SATA Controller should be displayed.  
2.  
3.  
Do18wnload from Www.Somanuals.com. All Manuals Search And Download.  
TechnicalSupportandWarranty  
QUESTIONS? SIIGs Online Support has answers! Simply visit our web site at  
www.siig.com and click Support. Our online support database is updated daily with  
new drivers and solutions. Answers to your questions could be just a few clicks away.  
You can also submit questions online and a technical support analyst will promptly  
respond.  
SIIG offers a 5-year manufacturer warranty with this product. This warranty covers the  
original purchaser and guarantees the product to be free of any defects in materials or  
workmanship for 5 years of the product.  
SIIG will, at our discretion, repair or replace (with an identical product or product  
having similar features and functionality) the product if defective in materials or  
workmanship. This warranty gives you specific legal rights, and you may also have other  
rights which vary from state to state. Please see our web site for more warranty details.  
If you encounter any problems with this product, please follow the procedures below.  
A) If it is within the store's return policy period, please return the product to the store  
where you purchased from.  
B) If your purchase has passed the store's return policy period, please follow the steps  
below to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Go to www.siig.com , click Support, then Request A Product Replacement to  
submit a request to SIIG RMA or fax a request to 510-657-5962. Your RMA request  
will be processed, if the product is determined to be defective, an RMA number will  
be issued.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All accessories that came with the  
original package must be included.  
Clearly write your RMA number on the top of the returned package. SIIG will  
refuse to accept any shipping package, and will not be responsible for a product  
returned without an RMA number posted on the outside of the shipping  
carton.  
You are responsible for the cost of shipping to SIIG. Ship the product to the  
following address:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
RMA #:  
SIIG will ship the repaired or replaced product via Ground in the U.S. and  
International Economy outside of the U.S. at no cost to the customer.  
19  
 
About SIIG, Inc.  
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity  
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,  
and legacy I/ O adapters) that bridge the connection between Desktop/  
Notebook systems and externalperipherals. SIIG continues to grow by adding  
A/ V and Digital Signage connectivity solutions to our extensive portfolio.  
SIIG products offer comprehensive user manuals,many user-friendly features,  
and are backed by an extensive manufacturer warranty. High quality control  
standards are evident by the overall ease of installation and compatibility of  
our products,as wellas one ofthe lowest defective return rates in the industry.  
SIIG products can be found in computer retail stores, mail order catalogs,  
through major distributors,system integrators,and VARs in the Americas and  
the UK, and through e-commerce sites.  
PRODUCT NAME  
DP eSATA 6Gb/s 2-Port PCIe  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B  
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is subject  
to the following two conditions: (1) This device may not cause harmful  
interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
Phone: 510-657-8688  
DP eSATA 6Gb/ s 2-Port PCIe is a trademark ofSIIG, Inc. SIIG and the SIIG logo are registered  
trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of Microsoft  
Corporation. All other names used in this publication are for identification only and may be  
trademarks of their respective owners.  
October, 2011  
Copyright © 2011 by SIIG, Inc. All rights reserved.  
 

Sharp Freezer SJ PT55R User Manual
Sigma Portable Generator BSG26N User Manual
Snapper Lawn Mower 1691423 User Manual
Sony Car Speaker XS R6941 User Manual
Sony Microcassette Recorder WM GX654 User Manual
Sony Speaker SRS D101 User Manual
Sony Turntable PS LX2 User Manual
Sony VCR SLV SE850G User Manual
SoundCraft Home Theater Server MH4 User Manual
Sunbeam Coffeemaker BVMC ECMP1000 User Manual