SIIG Computer Hardware 04 0721B User Manual

DP 1-Port ECP/EPP  
Parallel PCI  
Quick Installation Guide  
Introduction  
The DP 1-Port ECP/EPP Parallel PCI is a high-  
speed parallel card that provides one additional  
parallel port to your system.  
Key Features and Benefits  
Adds 1 ECP/EPP parallel port to your PCI  
based system  
Dual Profile design to work with standard  
height and low profile chassis  
Compliant with PCI Local Bus Specification,  
Revision 2.3  
Supports data transfer rate up to 1.5MB/s  
04-0721B  
1
 
HardwareInstallation  
General instructions for installing the card are  
provided below. Since the design of computer  
cases and motherboards vary, refer to your  
computer’ s reference manual for further  
information, if needed.  
Static Electricity Discharge may permanently  
damage your system. Discharge any static  
electricity build up in your body by touching your  
computer’ s case for a few seconds. Avoid any  
contact with internal parts and handle cards  
only by their external edges. Note: For low profile  
chassis, remove the standard height bracket and  
install the enhanced low-profile bracket now.  
1.  
2.  
3.  
Turn OFF the power to your computer and  
any other connected peripheral devices.  
Unplug the power cord and remove the  
cover from the computer.  
Remove the slot bracket from an available  
PCI slot.  
3
 
4.  
To install the card, carefully align the card's  
bus connector with the selected PCI slot on  
the motherboard. Push the board down  
firmly, but gently, until it is well seated.  
Replace the slot bracket's holding screw to  
secure the card.  
5.  
6.  
Replace the computer cover and reconnect  
the power cord.  
DriverInstallation  
This section provides information on how to  
install the DP 1-Port ECP/EPP Parallel PCI drivers.  
Windows 8 (32-/64-bit) / Windows 7 (32-/  
64-bit)  
1.  
Install the board and boot up Windows.  
Note: Windows 7 will automatically search  
preconfigured driver folders for the proper  
driver,thisprocessmaytakeseveralminutes  
to complete. Do not interrupt this process.  
2.  
Right click Computer, click Manage, click  
Device Manager.  
4
 
3.  
InsertthedriverCD. Rightclick PCIParallel  
Port, click Update Driver Software. Close  
the AutoPlay box if displayed.  
4.  
5.  
Click Browse my computer for driver  
software.  
For 32-bit: Type in D:\32-bit, then click  
Next. (Change D: to match your CD/  
DVD-ROM drive letter)  
For 64-bit: Type in D:\64-bit, then click  
Next. (Change D: to match your CD/  
DVD-ROM drive letter)  
6.  
At Windows has successfully updated  
your driver software, click Close to  
complete the installation.  
Windows Vista (32-/64-bit)  
1.  
2.  
Install the board and boot up Windows.  
At the Found New Hardware window,  
click Locate and install driver software  
(recommended), then click Continue.  
Click I don't have the disk. Show me other  
options.  
3.  
4.  
Insert the driver CD. Click Browse my  
computer for driver software.  
5
 
5.  
6.  
For 32-bit: Type in D:\32-bit, then click  
Next. (Change D: to match your CD/  
DVD-ROM drive letter)  
For 64-bit: Type in D:\64-bit, then click  
Next. (Change D: to match your CD/  
DVD-ROM drive letter)  
At The software for this device has been  
successfully installed, click Close to  
complete the installation.  
Windows XP (32-/64-bit) / Server 2003  
(32-/64-bit)  
1.  
2.  
Install the board and boot up Windows.  
At the Found New Hardware Wizard,  
select No, not this time, click Next. (Skip  
this step if not prompted)  
3.  
4.  
Select Install from a list or specific  
location, then click Next.  
Insert the driver CD. Select Include this  
location in the search, uncheck the other  
box.  
For 32-bit: Type in D:\32-bit, then click  
Next. (Change D: to match your CD/  
DVD-ROM drive letter)  
6
 
For 64-bit: Type in D:\64-bit, then click  
Next. (Change D: to match your CD/  
DVD-ROM drive letter)  
5.  
Click Finish to complete the installation.  
Windows Server 2008 (32-/64-bit)  
1.  
2.  
Install the board and boot up Windows.  
At the Found New Hardware window,  
click Locate and install driver software  
(recommended).  
3.  
4.  
5.  
Insert the driver CD.  
Click Don't search online.  
Click I don't have the disc. Show me other  
options.  
6.  
7.  
Click Browse my computer for driver  
software (advanced).  
For 32-bit: Type in D:\32-bit, then click  
Next. (Change D: to match your CD/  
DVD-ROM drive letter)  
For 64-bit: Type in D:\64-bit, then click  
Next. (Change D: to match your CD/  
DVD-ROM drive letter)  
8.  
Click Close to complete the installation.  
7
 
Windows Server 2008 R2  
1.  
Install the board and boot up Windows.  
2.  
Right click Computer, clickManage, double  
Diagnostics, then click Device Manager.  
InsertthedriverCD. RightclickPCIParallel  
Port, click Update Driver Software. Close  
the AutoPlay box if displayed.  
Click Browse my computer for driver  
software.TypeinD:\64-bit,thenclickNext.  
(Change D: to match your CD/DVD-ROM  
drive letter)  
3.  
4.  
6.  
At Windows has successfully updated  
your driver software, click Close to  
complete the installation.  
Windows 2000  
1.  
2.  
3.  
At the Found New Hardware Wizard, click  
Next.  
Select Search for a suitable driver for my  
device (recommended), then click Next.  
Check Specify a location, uncheck the other  
options and click Next.  
8
 
4.  
5.  
Insert the driver CD, type in D:\2000, then  
click OK. (Change D: to match your CD/  
DVD-ROM drive letter)  
Click Next, then click Finish to complete  
the installation.  
To Verify Windows Installation  
1.  
Check in Device Manager to verify  
installation.  
For Windows 8 / 7: Right click Computer,  
click Manage, then click Device Manager.  
For Windows Vista: Right click Computer,  
click Manage, click Continue, then click  
Device Manager.  
For Windows XP / Server 2003 / 2000: Right  
click My Computer, click Manage, click  
Device Manager.  
For Windows Server 2008 / Server 2008 R2:  
Right clickComputer, clickManage, double  
click Diagnostics, then click Device  
Manager.  
2.  
Click on the + (plus sign) in front of Ports  
(COM & LPT), and a PCI ECP Parallel  
Port... should be displayed.  
9
 
Windows ME  
1.  
At the Add New Hardware Wizard, select  
Specify the location of the driver  
(Advanced), click Next.  
2.  
Check Specify a location, uncheck the other  
box, insert the driver CD, type in D:\ME,  
then click Next. (Change D: to match your  
CD/DVD-ROM drive letter)  
3.  
4.  
Click Next, then Finish.  
Click Yes to restart Windows to complete  
the installation.  
Windows 98SE / 98  
1.  
2.  
3.  
At the Add New Hardware Wizard, click  
Next.  
Select Search for the best driver for your  
device. (Recommended), then click Next.  
Select Specify a location, uncheck the other  
boxes, insert the driver CD, type in D:\9x,  
then click Next. (Change D: to match your  
CD/DVD-ROM drive letter)  
10  
 
4.  
5.  
Click Next, then Finish. If prompted, at the  
Insert Disk box click OK. Insert your  
Windows 98 Installation CD-ROM then  
click OK.  
Click Yes to restart Windows to complete  
the installation.  
Windows 95  
1.  
2.  
3.  
At the Update Device Driver Wizard, click  
Next.  
Insert the driver CD, and click Other  
Locations.  
Type in D:\9x, click OK, then Finish.  
(Change D: to match your CD-ROM drive  
letter)  
4.  
5.  
From the Insert Disk window, click OK.  
WhentheCopyingFilesdialogboxappears,  
type in D:\9x, then click OK. (Change D: to  
match your CD/DVD-ROM drive letter)  
Click Yes to restart Windows to complete  
the installation.  
11  
 
To Verify Windows ME / 98SE / 98 / 95  
Installation  
1.  
From the Windows desktop, double click  
My Computer, Control Panel, System, then  
click Device Manager.  
2.  
Double click Ports (COM & LPT), M65-PCI  
ECP Parallel Port.....should be displayed.  
12  
 
ChangingParallelPortNumber  
Windows 8 / 7 / Vista / XP / 2003 / 2008 /  
2008 R2 / 2000  
Some parallel port devices need a specific LPT in  
order to function properly. If your parallel port  
device works, do not make any changes. Note:  
this feature is not available in Windows ME /  
98SE / 98 / 95.  
1.  
Right click Computer or My Computer,  
click Manage, then click Device Manager.  
Click on the + (plus sign) in front of Ports  
(COM & LPT), double click the PCI ECP  
Parallel Port.  
2.  
3.  
4.  
Click the Port Settings tab.  
Click the down arrow next to the LPT Port  
Number box, then select a parallel port that  
is not in use.  
5.  
Click OK to save the changes.  
13  
 
Blank Page  
14  
 
TechnicalSupportandWarranty  
QUESTIONS? SIIGs Online Support has answers! Simply visit our web site at  
www.siig.com and click Support. Our online support database is updated daily with  
new drivers and solutions. Answers to your questions could be just a few clicks away.  
You can also submit questions online and a technical support analyst will promptly  
respond.  
SIIG offers a 2-year manufacturer warranty with this product. This warranty covers the  
original purchaser and guarantees the product to be free of any defects in materials or  
workmanship for two (2) years from the date of purchase of the product.  
SIIG will, at our discretion, repair or replace (with an identical product or product  
having similar features and functionality) the product if defective in materials or  
workmanship. This warranty gives you specific legal rights, and you may also have other  
rights which vary from state to state. Please see our web site for more warranty details.  
If you encounter any problems with this product, please follow the procedures below.  
A) If it is within the store's return policy period, please return the product to the store  
where you purchased from.  
B) If your purchase has passed the store's return policy period, please follow the steps  
below to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Goto www.siig.com,clickSupport, thenREQUESTAPRODUCTREPLACEMENT  
to submit a request to SIIG RMA or fax a request to 510-657-5962. Your RMA request  
will be processed, if the product is determined to be defective, an RMA number will  
be issued.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All accessories that came with the  
original package must be included.  
Clearly write your RMA number on the top of the returned package. SIIG will  
refuse to accept any shipping package, and will not be responsible for a product  
returned without an RMA number posted on the outside of the shipping  
carton.  
You are responsible for the cost of shipping to SIIG. Ship the product to the  
followingaddress:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
RMA #:  
SIIG will ship the repaired or replaced product via Ground in the U.S. and  
International Economy outside of the U.S. at no cost to the customer.  
15  
 
About SIIG, Inc.  
Founded in 1985, SIIG, Inc. is a leading manufacturer of IT connectivity  
solutions (including Serial ATA and Ultra ATA Controllers, FireWire, USB,  
and legacy I/O adapters) that bridge the connection between Desktop/  
Notebooksystemsandexternalperipherals. SIIGcontinuestogrowbyadding  
A/V and Digital Signage connectivity solutions to our extensive portfolio.  
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendlyfeatures,  
andarebackedbyanextensivemanufacturerwarranty. Highqualitycontrol  
standards are evident by the overall ease of installation and compatibility of  
ourproducts,aswellasoneofthelowestdefectivereturnratesintheindustry.  
SIIG products can be found in computer retail stores, mail order catalogs,  
throughmajordistributors,systemintegrators,andVARsintheAmericasand  
theUK, andthroughe-commercesites.  
PRODUCT NAME  
DP 1-Port ECP/EPP Parallel PCI  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B  
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is subject  
to the following two conditions: (1) This device may not cause harmful  
interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
Phone: 510-657-8688  
DP 1-Port ECP/EPP Parallel PCI is a trademark of SIIG, Inc. SIIG and the SIIG logo are  
registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of  
Microsoft Corporation. All other names used in this publication are for identification only  
and may be trademarks of their respective owners.  
December, 2012  
Copyright © 2012 by SIIG, Inc. All rights reserved.  
 

Singer Sewing Machine 12W214 User Manual
Singer Sewing Machine 143G2 User Manual
Snapper Lawn Mower 1600207 User Manual
Solo USA Blower Port 423 User Manual
Sony Ericsson Headphones HBH PV712 User Manual
Sony Laptop VPCYB User Manual
Sony VCR SLV 775HF User Manual
Sony Video Game Console PSP 1006 K User Manual
Sylvania Indoor Furnishings 20676 User Manual
T+A Elektroakustik CD Player K1 CD RECEIVER User Manual