SIIG Computer Drive 5090S User Manual

2.5"USB2.0toSATAEnclosure  
Quick Installation Guide  
Introducing the USB 2.0 2.5" Enclosure  
The 2.5" USB 2.0 to SATA Enclosure is designed to  
supportUSBequippedcomputers. Thisenclosure  
provides large capacity mobile storage using 2.5"  
SATA hard disk drives through High-Speed USB  
2.0, hot-swapping interface.  
Key Features and Benefits  
Quickly adds more storage space to your  
USB-enabled PC  
No driver installation required. Simply  
install a 2.5" SATA (3 Gb/s or 1.5 Gb/s)  
hard disk into the enclosure then connect to  
a USB port  
Supports Hi-Speed USB 2.0 data transfer  
rate up to 480 Mb/s  
Compliant with Universal Serial Bus 2.0  
Specification  
04-0651A  
1
 
USB power connector  
(for extra power)  
USB data  
connector  
Figure 2: USB cable  
HardwareInstallation  
The following section guides you through the  
installation of your drive kit.  
Installing a 2.5" Hard Drive  
1.  
Remove the 2 screws in each side, see Figure  
3. Slide the top cover out of the case, then  
slide the lower cover out of the case, see  
Figure 4.  
Screws  
Screws  
Figure 3  
Figure 4  
3
 
2.  
Take off the PCB and connect it to the hard  
disk drive, see Figure 5 and Figure 6.  
Figure 5  
Figure 6  
Do4wnload from Www.Somanuals.com. All Manuals Search And Download.  
3.  
Put the installed PCB with hard disk drive  
into the hard disk drive tray, see Figure 7.  
Figure 7  
4.  
Hold onto the hard disk drive and turn the  
hard disk drive tray over. Secure the hard  
disk drive with four mounting screws, see  
Figure 8.  
Screw  
holes  
Screw  
holes  
Figure 8  
5
 
5.  
Slide the lower cover back into the case and  
secure it with the two mounting screws,  
then slide the upper cover back into the case  
and secure it with the two mounting screws.  
Use the included USB 2.0 data cable to plug  
the 2.5" USB 2.0 to SATA Enclosure into the  
computer.  
Plug the optional USB power cable into a  
reliable USB port. This step is only needed  
when the USB data connector doesn't  
provide enough power to power up the  
enclosure.  
6.  
7.  
8.  
The 2.5" USB 2.0 to SATA Enclosure will  
turn on automatically. Make sure that the  
LED is lit.  
Go to Driver Installation to complete the  
installation in the next page.  
DriverInstallation  
Windows will automatically detect and install  
drivers for the 2.5" USB 2.0 to SATA Enclosure.  
No additional driver installation is needed.  
Do6wnload from Www.Somanuals.com. All Manuals Search And Download.  
Using the 2.5" USB 2.0 to SATA  
Enclosure  
An additional drive icon will appear in My  
Computer or Computer when the enclosure is  
plugged into a USB port. The drive acts just like  
a conventional hard drive in your system.  
Disconnecting From The Computer  
Before unplugging the 2.5" USB 2.0 to SATA  
Enclosure from the computer, follow the steps  
below for your version of Windows. The same  
rule applies when turning off the Enclosure. Not  
following the instructions may result in data  
corruption or damage to the hard drive.  
Windows 7  
1.  
Verify that the LED is not flashing before  
proceeding.  
2.  
Click Show hidden icons, click the Safely  
Remove Hardware and Eject Media icon  
located in the system tray by the system  
clock.  
3.  
Click Eject USB to Serial-ATA bridge.  
7
 
4.  
You can now unplug or turn off the 2.5"  
USB 2.0 to SATA Enclosure.  
Windows Vista / Server 2008  
1.  
Verify that the LED is not flashing before  
proceeding.  
2.  
Click the Safely Remove Hardware icon  
located in the system tray by the system  
clock.  
3.  
4.  
Click Safely remove USB Mass Strorage  
Device, then click OK.  
You can now unplug or turn off the 2.5"  
USB 2.0 to SATA Enclosure.  
Windows XP / Server 2003  
1.  
Verify that the LED is not flashing before  
proceeding.  
2.  
Double click the Safely Remove Hardware  
icon located in the system tray by the system  
clock.  
3.  
4.  
Highlight Mass Storage Device, click Stop,  
OK, OK then Close.  
You can now unplug or turn off the 2.5"  
USB 2.0 to SATA Enclosure.  
Do8wnload from Www.Somanuals.com. All Manuals Search And Download.  
Windows 2000 SP4  
1.  
Verify that the HDD LED is ON or not  
blinking.  
2.  
Double click the Unplug or Eject Hardware  
icon located in the system tray by the system  
clock.  
3.  
4.  
Highlight USB Mass Storage Device, click  
Stop, OK, OK, then click Close.  
You can now unplug or turn off the 2.5"  
USB 2.0 to SATA Enclosure.  
9
 
Blank Page  
Do10wnload from Www.Somanuals.com. All Manuals Search And Download.  
TechnicalSupportandWarranty  
QUESTIONS? SIIGs Online Support has answers! Simply visit our web site at  
www.siig.com and click Support. Our online support database is updated daily with  
new drivers and solutions. Answers to your questions could be just a few clicks away. You  
can also submit questions online and a technical support analysts will promptly respond.  
SIIG offers a 5-year manufacturer warranty with this product. This warranty covers the  
original purchaser and guarantees the product to be free of any defects in materials or  
workmanship for five (5) years from the date of purchase of the product.  
SIIG will, at our discretion, repair or replace (with an identical product or product having  
similar features and functionality) the product if defective in materials or workmanship.  
This warranty gives you specific legal rights, and you may also have other rights which  
vary from state to state. Please see our web site for more warranty details.  
If you encounter any problems with this product, please follow the procedures below.  
A) If it is within the store's return policy period, please return the product to the store  
where you purchased from.  
B) If your purchase has passed the store's return policy period, please follow the steps  
below to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Go to www.siig.com, click Support, then RMA to submit a request to SIIG RMA or  
fax a request to 510-657-5962. Your RMA request will be processed, if the product  
is determined to be defective, an RMA number will be issued.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All accessories that came with the  
original package must be included.  
Clearly write your RMA number on the top of the returned package. SIIG will  
refuse to accept any shipping package, and will not be responsible for a product  
returned without an RMA number posted on the outside of the shipping  
carton.  
You are responsible for the cost of shipping to SIIG. Ship the product to the  
followingaddress:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
RMA #:  
SIIG will ship the repaired or replaced product via Ground in the U.S. and  
International Economy outside of the U.S. at no cost to the customer.  
11  
 
About SIIG, Inc.  
Foundedin1985,SIIG,Inc.isaleadingmanufacturerofITconnectivitysolutions  
(includingSerialATAandUltraATAControllers,FireWire,USB,andlegacyI/  
Oadapters)thatbridgetheconnectionbetweenDesktop/Notebooksystemsand  
external peripherals. SIIG continues to grow by adding A/V and Digital  
Signageconnectivitysolutionstoourextensiveportfolio.  
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendlyfeatures,  
and are backed by an extensive manufacturer warranty. High quality control  
standards are evident by the overall ease of installation and compatibility of  
ourproducts, aswellasoneofthelowestdefectivereturnratesintheindustry.  
SIIG products can be found in computer retail stores, mail order catalogs,  
throughmajordistributors, systemintegrators, andVARsintheAmericasand  
theUK,andthroughe-commercesites.  
PRODUCT NAME  
2.5" USB 2.0 to SATA Enclosure  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B  
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is subject  
to the following two conditions: (1) This device may not cause harmful  
interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
Phone: 510-657-8688  
2.5" USB 2.0 to SATA Enclosure is a trademark of SIIG, Inc. SIIG and the SIIG logo are  
registered trademarks of SIIG, Inc. Microsoft and Windows are registered trademarks of  
MicrosoftCorporation. Allothernamesusedinthispublicationareforidentificationonlyand  
may be trademarks of their respective owners.  
October, 2010  
Copyright © 2010 by SIIG, Inc. All rights reserved  
 

SIIG Network Card 04 0832A User Manual
Singer Sewing Machine 132K1 User Manual
Singer Sewing Machine CXL User Manual
Sony Ericsson Cell Phone MK16a User Manual
Sony Personal Computer Vaio Series User Manual
Sony Portable CD Player MDX CA680 User Manual
Sony Radio SRF M97 User Manual
Sony Speaker SS LA500ED User Manual
Stanley Black Decker Food Saver GT18B01 User Manual
Sylvania TV VCR Combo 6309CC User Manual