SIIG Computer Drive 04 0643B User Manual

SuperSpeed USB 3.0 to  
SATA 2.5" Enclosure  
Quick Installation Guide  
IntroducingtheUSB3.02.5"Enclosure  
The SuperSpeed USB 3.0 to SATA 2.5" Enclosure is  
designed to support USB equipped computers.  
This enclosure provides large capacity mobile  
storage using 2.5" SATA hard disk drives through  
hot-swapping SuperSpeed USB 3.0 interface.  
Key Features and Benefits  
Quickly adds more storage space to your  
USB-enabled PC (USB 3.0 recommended)  
No driver installation required. Simply  
install a 2.5" SATA (3Gb/s or 1.5Gb/s)  
hard disk into the enclosure then connect to  
a USB port  
Note: For maximum data throughput, use  
a SATA 3Gb/s hard disk with the  
enclosure and connect to a fully functional  
USB 3.0 port.  
04-0643B  
1
 
USB 3.0 Y-split Cable  
USB Data Connector (to computer)  
USB Data Connector (to enclosure)  
USB Power Connector (to  
computer, optional)  
Figure 2: USB 3.0 Y-split Cable  
3
 
HardwareInstallation  
The following section guides you through the  
installation of your drive kit.  
Installing a 2.5" Hard Drive  
1.  
Remove the 2 screws in each side, see Figure  
3. Slide the top cover out of the case, then  
slide the lower cover out of the case, see  
Figure 4.  
screws  
screws  
Figure 3  
Figure 4  
Do4wnload from Www.Somanuals.com. All Manuals Search And Download.  
2.  
Take off the PCB and connect it to the hard  
disk drive, see Figure 5 and Figure 6.  
Figure 5  
Figure 6  
5
 
3.  
Put the installed PCB with hard disk drive  
into the hard disk drive tray, see Figure 7.  
Figure 7  
4.  
Hold onto the hard disk drive and turn the  
hard disk drive tray over. Secure the hard  
disk drive with four mounting screws, see  
Figure 8.  
Screw  
holes  
Screw  
holes  
Figure 8  
Do6wnload from Www.Somanuals.com. All Manuals Search And Download.  
5.  
Slide the lower cover back into the case and  
secure it with the two mounting screws,  
then slide the upper cover back into the case  
and secure it with the two mounting screws.  
Plug the included USB 3.0 cable into the  
enclosure. (Use the cable end with the single  
Type A USB connector).  
6.  
7.  
Plug the USB Data Connector, see Figure 2  
on page 3, into a USB port of the computer.  
Important:In most cases the USB Data  
Connector will supply enough power to  
the enclosure. If not, use the optional USB  
Power Connector to supply more power.  
Before proceeding, first unplug the USB  
Data Connector, then plug the USB Power  
Connector into an available USB port,  
then re-plug the USB Data Connector.  
8.  
The SuperSpeed USB 3.0 to SATA 2.5"  
Enclosure will turn on automatically. Make  
sure that the LED is lit.  
Go to Driver Installation to complete the  
installation.  
7
 
DriverInstallation  
Windows will automatically detect and install  
drivers for the SuperSpeed USB 3.0 to SATA 2.5"  
Enclosure. No additional driver installation is  
needed.  
Using the SuperSpeed USB 3.0 to  
SATA2.5"Enclosure  
An additional drive icon will appear in My  
Computer when the enclosure is plugged into a  
USB port. The drive acts just like a conventional  
hard drive in your system.  
Disconnecting From The Computer  
Before unplugging the SuperSpeed USB 3.0 to  
SATA 2.5" Enclosure from the computer, follow  
the steps below for your version of Windows.  
The same rule applies when turning off the  
Enclosure. Not following the instructions may result  
in data corruption or damage to the hard disk drive.  
Do8wnload from Www.Somanuals.com. All Manuals Search And Download.  
Windows 7  
1.  
Verify that the LED is not flashing before  
proceeding.  
2.  
Click Show hidden icons, click the Safely  
Remove Hardware and Eject Media icon  
located in the system tray by the system  
clock.  
3.  
4.  
Click Eject USB Mass Storage Device.  
You can now unplug or turn off the  
SuperSpeed USB 3.0 to SATA 2.5" Enclosure.  
Windows Vista / Server 2008  
1.  
Verify that the LED is not flashing before  
proceeding.  
2.  
Click the Safely Remove Hardware icon  
located in the system tray by the system  
clock.  
3.  
4.  
Click Safely remove USB Mass Strorage  
Device, then click OK.  
You can now unplug or turn off the  
SuperSpeed USB 3.0 to SATA 2.5" Enclosure.  
9
 
Windows XP / Server 2003  
1.  
Verify that the LED is not flashing before  
proceeding.  
2.  
Double click the Safely Remove Hardware  
icon located in the system tray by the system  
clock.  
3.  
4.  
Highlight Mass Storage Device, click Stop,  
OK, OK, then Close.  
You can now unplug or turn off the  
SuperSpeed USB 3.0 to SATA 2.5" Enclosure.  
Do10wnload from Www.Somanuals.com. All Manuals Search And Download.  
TechnicalSupportandWarranty  
QUESTIONS? SIIGs Online Support has answers! Simply visit our web site at  
www.siig.com and click Support. Our online support database is updated daily with  
new drivers and solutions. Answers to your questions could be just a few clicks away.  
You can also submit questions online and a technical support analyst will promptly  
respond.  
SIIG offers a 5-year manufacturer warranty with this product. This warranty covers the  
original purchaser and guarantees the product to be free of any defects in materials or  
workmanship for five (5) years from the date of purchase of the product.  
SIIG will, at our discretion, repair or replace (with an identical product or product  
having similar features and functionality) the product if defective in materials or  
workmanship. This warranty gives you specific legal rights, and you may also have other  
rights which vary from state to state. Please see our web site for more warranty details.  
If you encounter any problems with this product, please follow the procedures below.  
A) If it is within the store's return policy period, please return the product to the store  
where you purchased from.  
B) If your purchase has passed the store's return policy period, please follow the steps  
below to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Go to www.siig.com, click Support, then RMA to submit a request to SIIG RMA or  
fax a request to 510-657-5962. Your RMA request will be processed, if the product  
is determined to be defective, an RMA number will be issued.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All accessories that came with the  
original package must be included.  
Clearly write your RMA number on the top of the returned package. SIIG will  
refuse to accept any shipping package, and will not be responsible for a  
product returned without an RMA number posted on the outside of the  
shipping carton.  
You are responsible for the cost of shipping to SIIG. Ship the product to the  
followingaddress:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
RMA #:  
SIIG will ship the repaired or replaced product via Ground in the U.S. and  
International Economy outside of the U.S. at no cost to the customer.  
11  
 
About SIIG, Inc.  
Foundedin1985,SIIG,Inc.isaleadingmanufacturerofITconnectivitysolutions  
(including Serial ATA and Ultra ATA Controllers, FireWire, USB, and legacy  
I/Oadapters)thatbridgetheconnectionbetweenDesktop/Notebooksystems  
and external peripherals. SIIG continues to grow by adding A/V and Digital  
Signageconnectivitysolutionstoourextensiveportfolio.  
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendlyfeatures,  
and are backed by an extensive manufacturer warranty. High quality control  
standards are evident by the overall ease of installation and compatibility of  
ourproducts, aswellasoneofthelowestdefectivereturnratesintheindustry.  
SIIG products can be found in computer retail stores, mail order catalogs,  
throughmajordistributors,systemintegrators,andVARsintheAmericasand  
theUK,andthroughe-commercesites.  
PRODUCT NAME  
SuperSpeed USB 3.0 to SATA 2.5" Enclosure  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS B  
OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is subject  
to the following two conditions: (1) This device may not cause harmful  
interference, and (2) this device must accept any interference received,  
including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
Phone: 510-657-8688  
SuperSpeedUSB 3.0 to SATA 2.5" Enclosure is a trademark of SIIG, Inc. SIIG and the SIIG  
logoareregisteredtrademarksofSIIG,Inc. MicrosoftandWindowsareregisteredtrademarks  
of Microsoft Corporation. All other names used in this publication are for identification only  
and may be trademarks of their respective owners.  
January, 2011  
Copyright © 2011 by SIIG, Inc. All rights reserved  
 

Sharp Cash Register XE A42S User Manual
Snapper Lawn Aerator 4808 User Manual
Sony Bluetooth Headset DRBT140Q User Manual
Sony DVD Player 3 283 146 112 User Manual
Sony MP3 Player WM FS595 User Manual
Sony Portable CD Player VGF AP1 User Manual
Star Micronics Printer 10DK User Manual
Star Tech Development Exercise Bike 35FCREAD20 User Manual
Stiga Lawn Mower 45 S User Manual
Superior Cell Phone W880I User Manual