SIIG Computer Drive 04 0265F User Manual

Serial ATA PCI  
Quick Installation Guide  
Introducing the Serial ATA PCI  
The Serial ATA PCI is an ultra high-speed dual channel  
Serial ATA controller board for use in Pentium-class  
computers. It achieves burst data transfer rates up to  
150MB/s (1.5Gb/s) and supports various brand of hard  
disk drives with capacities greater that 137GB.  
FeaturesandBenefits  
Add up to two high-speed SATA hard drives  
New Serial ATA cable - easier to install & provides  
better air circulation  
Compliant with Serial ATA 1.0 specification  
Compliant with PCI 2.3 specification  
Supports data transfer rate up to 1.5Gb/s  
(150MB/s)  
Two independent bus master DMA channels with  
256-byteFIFOsperchannelforhostreadsandwrites  
Breaksthe137GBbarrier!Workswithvariousbrands  
of large capacity Serial ATA hard disk drives  
SystemRequirements  
Pentium® or equivalent PC with an available PCI  
slot  
Windows® 98SE / ME / NT4.0 / 2000 / XP (32-/64-  
bit) / Server 2003 & 2008 (32-/64-bit) / Vista (32-/  
64-bit)  
1
04-0265F  
 
1. Turn OFF the power to your computer and any  
other connected peripheral devices.  
2. Unplug the power cord from the back of the  
computer.  
3. Remove the computer cover.  
4. Remove the slot bracket from an available PCI slot.  
5. To install the card, carefully align the card bus  
connector to the selected PCI slot on the  
motherboard. Push the board down firmly, but  
gently, until it is well seated.  
6. Replace the slot bracket holding screw to secure the  
card.  
DeviceConnection  
TheSerialATAPCIisadualchannelSerialATAcontroller  
that supports up to two Serial ATA hard disk drives. If  
you plan to use the second Serial ATA channel, you will  
need to purchase another Serial ATA cable.  
1. Install hard disk drive(s) in chassis.  
2. ConnecttheSerialATAharddiskdrivetothesystem  
power supply using the Serial ATA power cable.  
3. Connect one end of the Serial ATA cable to the hard  
disk drive.  
Serial ATA cable  
Serial ATA power  
cable  
Figure 2: Hard disk drive connecrions  
4. Attach the other end of the Serial ATA cable to the  
Serial ATA connector on the Serial ATA PCI.  
3
 
Serial ATA  
cable  
Figure 3. Connecting the Serial ATA cable  
5. Follow the same instructions when connecting a  
second hard drive. Device connection is now  
complete.  
6. Replacethecomputercoverandreconnectthepower  
cord.  
Driver Installation  
This section provides information on how to install the  
Serial ATA PCI drivers.  
Windows98SE  
For New Windows 98SE Installation  
1. Install the board and follow Microsoft procedures  
to install Windows 98SE accordingly.  
2. Once Windows has been installed, right click My  
Computer and click Properties. Select Device  
Manager tab.  
3. Double click PCI Mass Storage Controller listed  
under Other Devices.  
4. Select Driver tab, then click Update Driver button.  
5. Insert the driver CD and click Next.  
4
 
6. Select Search for a better driver..., then click Next.  
7. Check Specify a location, uncheck the other boxes,  
then click Next.  
8. Click Next, then click Finish.  
9. Remove the driver CD and restart Windows to  
complete the installation.  
For Existing Windows 98SE Installation  
1. Install the board and boot up Windows.  
2. At the Add New Hardware Wizard, click Next.  
3. SelectSearchforthebestdriverforyourdeviceand  
click Next.  
4. Insert the driver CD, check Specify a location,  
uncheck the other boxes, type D:\98SE, then click  
Next. (Change D: to match the drive letter of your  
CD-ROM)  
5.  
Click Next, then Finish.  
6. Remove the driver CD and restart Windows to  
complete the installation.  
WindowsME  
For New Windows ME Installation  
1. Install the board and follow Microsoft procedures  
to install Windows ME accordingly.  
2. Once Windows has been installed, right click My  
Computer, then click Properties. Select Device  
Manager tab.  
3. Double click PCI Mass Storage Controller listed  
under Other Devices.  
4. Select Driver tab, then click Update Driver button.  
5. Insert the driver CD, select Specify the location of  
the driver (Advanced), then click Next.  
5
 
6. Check Specify a location, uncheck the other box,  
type D:\ME, click Next. (Change D: to match the  
drive letter of your CD-ROM)  
7. ClickNext, thenclickFinish. RemovethedriverCD  
and restart Windows to complete the installation.  
For Existing Windows ME Installation  
1. Install the board and boot up Windows ME.  
2. AttheAddNewHardwareWizard,insertthedriver  
CD.  
3. SelectSpecifythelocationofthedriver(Advanced),  
then click Next.  
4. Check Specify a location, uncheck the other box,  
type D:\ME, click Next. (Change D: to match the  
drive letter of your CD-ROM)  
5. Click Next, then click Finish.  
6. Remove the driver CD and restart Windows to  
complete the installation.  
ToVerifyWindows98SE/MEInstallation  
1. Right-click My Computer, then click Properties.  
Select Device Manager tab.  
2. Double click SCSI controllers, Silicon Image SiI...  
Controller should be listed.  
3. Double click Silicon Image SiI... Controller and  
click Properties. A message This device is working  
properly is displayed in the dialog box when the  
driver is correctly installed.  
6
 
WindowsNT4.0  
For New Windows NT4.0 Installation  
A new installation of Windows NT4.0 requires a floppy  
disk for the driver installation. To make this floppy disk,  
copy the contents of the NT4 folder, found on the driver  
CD, onto a blank floppy disk then follow the directions  
below.  
1. Install the board and follow Microsoft procedures  
to install Windows NT4.0 accordingly.  
2. At the Windows NT Setup screen, press F6 to  
specify and add the driver.  
3. Press S, select Other, then press Enter.  
4. Insert the driver diskette then press Enter.  
5.  
Select Silicon Image... for Windows NT 4.0 and  
2000 and press Enter.  
6. Press Enter to continue, then follow the on-screen  
instructions to complete Windows NT4.0  
installation.  
For Existing Windows NT4.0 Installation  
1. Install the board and boot up Windows NT4.0.  
2. Double click My Computer/Control Panel/SCSI  
Adapters, then click the Drivers tab.  
3. Click Add..., then click Have Disk....  
4. Insert the driver CD, type D:\NT4, then click OK.  
(Change D: to match the drive letter of your  
CD-ROM)  
5. Highlight Silicon Image in the left column, then  
select Silicon Image SiI... SATALink Controller,  
and click OK.  
6. ClickOK,removethedriverCDandrestartNT4.0to  
complete the installation.  
7
 
ToVerifyWindowsNT4.0Installation  
1. Double click My Computer/Control Panel/SCSI  
Adapters.  
2. Highlight Silicon Image... Controller from SCSI  
Adapters listing and click Properties. A message  
This device is working properly is displayed in the  
dialog box when the driver is correctly installed.  
Windows2000  
For New Windows 2000 Installation  
A new installation of Windows 2000 requires a floppy  
disk for the driver installation. To make this floppy disk,  
copy the contents of the Floppy folder, found on the  
driver CD, onto a blank floppy disk then follow the  
directions below.  
1. Install the board and follow Microsoft procedures  
to install Windows 2000 accordingly.  
2. Restart your system when prompted during  
Windows' installation.  
3. At the Windows 2000 Setup screen, press F6 to  
install the driver.  
4. Insert the driver diskette. Press S, then press Enter.  
5. Select Silicon Image SiI... Controller and press  
Enter.  
6. Press Enter to continue and follow on-screen  
instructions to complete the installation.  
For Existing Windows 2000 Installation  
1. Install the board and boot up Windows 2000.  
2. At the Found New Hardware Wizard, click Next.  
3. Select Search for a suitable driver for my device  
(recommended) and click Next.  
8
 
4. InsertthedriverCD,checkCD-ROMdrives,uncheck  
the other boxes, and click Next. Click Next again to  
continue.  
5. Click Finish, remove the driver CD and restart  
Windows to complete the installation.  
WindowsXP/Server2003(32-bit)  
For New Windows XP/Server 2003 Installation  
A new installation of Windows XP/Server 2003 requires  
a floppy disk for the driver installation. To make this  
floppy disk, copy the contents of the Floppy folder,  
found on the driver CD, onto a blank floppy disk then  
follow the directions below.  
1. Install the board and follow Microsoft procedures  
to install Windows accordingly.  
2. Restart your system if prompted by Windows  
installation.  
3. At the Windows Setup screen, press F6 to install the  
driver.  
4. Insert the driver diskette. Press S then press Enter.  
5. Select Silicon Image SiI... Controller and press  
Enter.  
6. Press Enter to continue and follow the on-screen  
instructions to complete the installation.  
For Existing Windows XP/Server 2003 Installation  
1. Install the board and boot up Windows.  
2. At the Found New Hardware Wizard:  
XP (w/SP1 or earlier)/Server 2003: continue to step #3  
XP (w/SP2 or later)/Server 2003 (w/ SP1 or later): select  
No, not at this time, then click Next.  
3. Insert the driver CD, select Install the software  
automatically (Recommended), and click Next.  
9
 
4. Click Finish and restart Windows to complete the  
installation.  
Windows XP /Server 2003 (64-bit)  
For New Windows XP/2003 Installation  
A new installation of Windows XP 64-bit/Server 2003  
64-bit requires a floppy disk for the driver installation.  
To make this floppy disk, copy the contents of the 64bit  
folder, found on the driver CD, onto a blank floppy disk  
then follow the directions below.  
1. Install the board and follow Microsoft procedures  
to install Windows accordingly.  
2. Restart your system when prompted by Windows  
installation.  
3. At the Windows Setup screen, press F6 to install the  
driver.  
4.  
Insert the floppy disk you made above. Press S then  
press Enter.  
5. Select Silicon Image SiI 3512... that matches your  
system processor, then press Enter.  
6. Press Enter to continue and follow the on-screen  
instructions to complete the installation.  
For Existing Windows XP/2003 Installation  
1. Install the board and boot up Windows.  
2. AttheFoundNewHardwareWizard,selectNo,not  
at this time, then click Next.  
3. Insert the driver CD, select Install the software  
automatically (Recommended), and click Next.  
4. Click Finish and restart Windows to complete the  
installation.  
10  
 
ToVerifyWindows2000/XP/2003Installation  
1. Right click My Computer and click Manage.  
2. Select Device Manager.  
3. Double click SCSI and RAID Controllers, Silicon  
Image SiI 3512... Controller should be displayed.  
WindowsVista(32-bit)  
For New Windows Vista Installation  
1. Install the board and follow Microsoft procedures  
to install Windows Vista accordingly.  
2. At the Where do you want to install Windows?  
screen, click Load Driver.  
3. Insert the driver CD, then click OK.  
4. Select Silicon Image SiI... SATALink Controller...,  
then click Next.  
5. Follow the on-screen instructions to complete the  
Windows Vista installation.  
For Existing Windows Vista Installation  
1. At the Found New Hardware Wizard, click Locate  
and install driver software (recommended).  
2. Click Continue, insert the driver CD, click Next.  
3. Click Close to complete the installation.  
WindowsVista(64-bit)  
For New Windows Vista 64-bit Installation  
1. Install the board and follow Microsoft procedures  
to install Windows accordingly.  
2. At Where do yo want to install Windows? screen,  
click Load Drivers.  
3. Insert the driver CD, click Browse.  
11  
 
4. Clickonthe Plus(+)signnexttotheCD-ROMdrive,  
then double click the 64bit folder.  
5. Highlight AMD64 (for 64-bit extended processors)  
or IA64 (for 64-bit Intel Itanium processors), then  
click Ok.  
6. Select Silicon Image... SATALink Controller, then  
press Next.  
7. Follow the on-screen instructions to complete the  
installation.  
For Existing Windows Vista 64-bit Installation  
1. Install the board and boot up Windows.  
2. At the Found New Hardware Wizard, select Locate  
and install driver software (recommended), click  
Continue.  
3. Insert the driver CD, click Next.  
4. Click Close to complete the installation.  
To Verify Windows Vista Installation  
1. Right click My Computer and click Manage.  
2. Click Continue, click Device Manager.  
3. Double click Storage controllers, Silicon Image  
SiI... Controller should be displayed.  
WindowsServer2008(32-bit)  
New Windows 2008 Installation  
1. Install the board and follow Microsoft procedures  
to install Windows accordingly.  
2. At Where do you want to install Windows?, click  
Load Driver.  
3. Insert driver CD, then click Browse.  
4. Click CD Drive...Drivers, then click OK.  
12  
 
5. Select Silicon Image Sil 3512 SATALink  
Controller..., then click OK  
6. Followon-screeninstructionstocompleteWindows  
Server 2008 installation.  
Existing Windows 2008 Installation  
1. Install the board and boot up Windows.  
2. At the Found New Hardware Wizard, select Locate  
and install driver software (Recommended), then  
click Don't search online.  
3. Insert the driver CD. The driver will install  
automatically.  
4.  
Click Close.  
5. Remove the driver CD and restart your Windows to  
complete the installation.  
WindowsServer2008(64-bit)  
New Windows 2008 Installation  
1. Install the board and follow Microsoft procedures  
to install Windows accordingly.  
2. At Where do you want to install Windows?, click  
Load Driver.  
3. Insert driver CD, then click Browse.  
4. Double click CD Drive (D:). (change D: to match  
your CD-ROM drive letter)  
5. Double click 64bit folder, highlight AMD64 (for 64-  
bit extended processors) or IA64 (for 64-bit Intel  
Itanium processors), then click Ok.  
6. Select Silicon Image Sil 3512 SATALink  
Controller..., then click Next.  
7. Followon-screeninstructionstocompleteWindows  
Server 2008 installation.  
13  
 
Existing Windows 2008 Installation  
1. Install the board and boot up Windows.  
2. At the Found New Hardware Wizard, select Locate  
and install driver software (Recommended), then  
click Don't search online.  
3. Insert the driver CD. The driver will install  
automatically.  
4.  
Click Close.  
5. Remove the driver CD and restart your Windows to  
complete the installation.  
VerifyServer2008Installation  
1. Right click Computer, click Manage, double click  
Diagnostics, click Device Manager.  
2. Double click Storage controllers, Silicon Image  
SiI... Controller should be displayed.  
Bios Configuration  
The Serial ATA PCI BIOS will appear everytime your  
system starts up. If the bios doesn't show, please install  
your controller in another PCI slot. During this (Post)  
process, the bios will show up and indicate the devices  
attached to it.  
14  
 
Technical Support and Warranty  
QUESTIONS? SIIGsOnlineSupporthasanswers! Simplyvisitour  
web site at www.siig.com and click Support. Our online support  
database is updated daily with new drivers and solutions. Answers  
toyourquestionscouldbejustafewclicksaway. Youcanalsosubmit  
questions online and a technical support analysts will promptly  
respond.  
SIIGoffersalifetimemanufacturerwarrantywiththisproduct. Please  
see our web site for more warranty details. If you encounter any  
problems with this product, please follow the procedures below.  
A) If it is within the store's return policy period, please return the  
product to the store where you purchased from.  
B) Ifyourpurchasehaspassedthestore'sreturnpolicyperiod,please  
follow these steps to have the product repaired or replaced.  
Step 1: Submit your RMA request.  
Go to www.siig.com, click Support, then RMA to submit a  
request to SIIG RMA. If the product is determined to be  
defective, an RMA number will be issued.  
Step 2: After obtaining an RMA number, ship the product.  
Properly pack the product for shipping. All software, cable(s)  
and any other accessories that came with the original package  
must be included.  
Clearly write your RMA number on the top of the returned  
package. SIIG will refuse to accept any shipping package, and  
will not be responsible for a product returned without an  
RMA number posted on the outside of the shipping carton.  
You are responsible for the cost of shipping. Ship the product  
to the following address:  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
RMA#:  
SIIG will ship the repaired or replaced product via Ground  
in the U.S. and International Economy outside of the U.S. at  
no cost to the customer.  
15  
 
About SIIG, Inc.  
Foundedin1985,SIIG,Inc.isaleadingcomputerupgrademanufacturer  
ofI/Oconnectivityproducts,includingPCI&ISAserialandparallel  
ports, USB, Serial ATA & UltraATA controllers, FireWire (1394a/b),  
networking, sound cards, and other accessories. SIIG is the premier  
one-stop source of upgrades.  
SIIGproductsoffercomprehensiveusermanuals,manyuser-friendly  
features, and are backed by an extensive manufacturer warranty.  
High-quality control standards are evident by the overall ease of  
installation and compatibility of our products, as well as one of the  
lowest defective return rates in the industry. SIIG products can be  
found in computer retail stores, mail order catalogs, through major  
distributors, system integrators, and VARs in the Americas and the  
UK,andthroughe-commercesites.  
PRODUCT NAME  
SerialATAPCI  
FCC RULES: TESTED TO COMPLY WITH FCC PART 15, CLASS  
B OPERATING ENVIRONMENT: FOR HOME OR OFFICE USE  
FCCCOMPLIANCESTATEMENT:  
This device complies with part 15 of the FCC Rules. Operation is  
subject to the following two conditions: (1) This device may not cause  
harmful interference, and (2) this device must accept any interference  
received, including interference that may cause undesired operation.  
THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE  
SIIG, Inc.  
6078 Stewart Avenue  
Fremont, CA 94538-3152, USA  
Ph: 510-657-8688  
Serial ATA PCI is a trademark of SIIG, Inc. SIIG and the SIIG logo are registered trademarks of SIIG,  
Inc. Microsoft, Windows and Windows Vista are either registered trademarks or trademarks of  
MicrosoftCorporationintheUnitedStatesand/orothercountries. Pentiumisaregisteredtrademark  
of Intel Corporation. Other names used in this publication are for identification only and may be  
trademarksoftheirrespectivecompanies.  
March, 2009  
Copyright © 2009 by SIIG, Inc. All rights reserved.  
 

Sharp Car Video System PN V602 User Manual
Sharp Heat Pump AE Z48LZ User Manual
SIIG Computer Drive 04 0322B User Manual
Silex technology Printer SX 3000GB User Manual
Sony Car Stereo System CDX M9900 User Manual
Sony Home Theater System DAV DZ231 User Manual
Sony Network Card TDM BT1 User Manual
Sony Satellite Radio STR DE835 User Manual
SOYO Computer Hardware SY 6ZB User Manual
StarTechcom Network Cables PCMACLINK2 User Manual